參數資料
型號: ISP1160BD
廠商: NXP SEMICONDUCTORS
元件分類: 總線控制器
英文描述: Embedded Universal Serial Bus Host Controller
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, PQFP64
封裝: 10 X 10 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT-314-2, LQFP-64
文件頁數: 12/88頁
文件大?。?/td> 2044K
代理商: ISP1160BD
Philips Semiconductors
ISP1160
Embedded USB Host Controller
Product data
Rev. 04 — 04 July 2003
12 of 88
9397 750 11371
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
Figure 9
shows a complete access cycle of the HC internal FIFO buffer RAM. For a
write cycle, the microprocessor first writes the FIFO buffer RAM’s command code to
the command port, and then writes the data words one by one to the data port until
half of the transfer’s byte count is reached. The HcTransferCounter register (22H to
read, A2H to write) is used to specify the byte count of a FIFO buffer RAM’s read
cycle or write cycle. Every access cycle must be in the same access direction. The
read cycle procedure is similar to the write cycle.
8.5 FIFO buffer RAM access by DMA mode
The DMA interface between a microprocessor and the ISP1160 is shown in
Figure 4
.
When doing a DMA transfer, at the beginning of every burst the ISP1160 outputs a
DMA request to the microprocessor via pin DREQ. After receiving this signal, the
microprocessor will reply with a DMA acknowledge to the ISP1160 via pin DACK_N,
and at the same time, execute the DMA transfer through the data bus. In the DMA
mode, the microprocessor must issue a read or write signal to the ISP1160’s
pins RD_N or WR_N. The ISP1160 will repeat the DMA cycles until it receives an
EOT signal to terminate the DMA transfer.
The ISP1160 supports both external and internal EOT signals. The external EOT
signal is received as input on pin EOT, and generally comes from the external
microprocessor. The internal EOT signal is generated inside the ISP1160.
To select either EOT method, set the appropriate DMA configuration register (see
Section 10.4.2
). For example, setting DMACounterSelect (bit 2) of the
HcDMAConfiguration register (21H to read, A1H to write) to logic 1 will enable the
DMA counter for DMA transfer. When the DMA counter reaches the value of the
HcTransferCounter register, the internal EOT signal will be generated to terminate the
DMA transfer.
The ISP1160 supports either single-cycle DMA operation or burst mode DMA
operation; see
Figure 10
and
Figure 11
.
Fig 9.
Internal FIFO buffer RAM access cycle.
MGT941
read/write data
#1 (16 bits)
FIFO buffer RAM access cycle (transfer counter = 2N)
t
read/write data
#2 (16 bits)
read/write data
#N (16 bits)
write command
(16 bits)
相關PDF資料
PDF描述
ISP1160BM Embedded Universal Serial Bus Host Controller
ISP1161A Full-speed Universal Serial Bus single-chip host and device controller
ISP1161ABD Full-speed Universal Serial Bus single-chip host and device controller
ISP1161ABM Full-speed Universal Serial Bus single-chip host and device controller
ISP1161 Full-speed Universal Serial Bus single-chip host and device controller
相關代理商/技術參數
參數描述
ISP1160BD,157 功能描述:USB 接口集成電路 USB 1.1 HOST CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1160BD/01 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller
ISP1160BD/01,118 功能描述:USB 接口集成電路 USB HOST CTRL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1160BD/01,151 功能描述:USB 接口集成電路 USB FULL SPEED HOST RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1160BD/01,157 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20