- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1130 (NXP Semiconductors N.V.) Universal Serial Bus compound hub with integrated keyboard controller PDF資料下載
參數資料
| 型號： | ISP1130 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus compound hub with integrated keyboard controller |
| 中文描述： | 通用串行總線控制器與集成鍵盤復合樞紐 |
| 文件頁數： | 29/68頁 |
| 文件大?。?/td> | 1786K |
| 代理商： | ISP1130 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Philips Semiconductors
ISP1130
USB compound hub with keyboard controller
Objective specification
Rev. 01 — 23 March 2000
29 of 68
9397 750 06895
Philips Electronics N.V. 2000. All rights reserved.
9.2.7
Validate Buffer command
Indicates the presence of valid data for transmission to the USB host.
Code (Hex) —
FA
Transaction —
none.
After writing data into an endpoint’s IN buffer, the microcontroller must set the Buffer
Full flag by means of the Validate Buffer command. This indicates that the data in the
buffer are valid and can be sent to the host when the next IN token is received.
Remark:
A control IN buffer cannot be validated when the Packet Overwritten bit of
the corresponding OUT buffer is set.
9.2.8
Set Endpoint Status command
Stalls or unstalls the indicated endpoint.
Code (Hex) —
40 to 4B (endpoint index 0 to 11)
Transaction —
write 1 byte.
A stalled control endpoint is automatically unstalled when it receives a SETUP token,
regardless of the content of the packet. If the endpoint should stay in its stalled state,
the microcontroller can re-stall it with the Set Endpoint Status command.
When a stalled endpoint is unstalled (either by the Set Endpoint Status command or
by receiving a SETUP token), it is also re-initialized. This flushes the buffer: in and if it
is an OUT buffer it waits for a DATA 0 PID, if it is an IN buffer it writes a DATA 0 PID.
Remark:
A Set Endpoint Status command with a STALLED bit of logic 0 will always
initialize the endpoint, even when it was not stalled.
Table 32: Packet Status byte: bit allocation
Bit
7
Symbol
-
6
-
5
-
4
-
3
-
2
-
1
-
0
Packet
Overwritten
0
R
Reset
Access
X
R
X
R
X
R
X
R
X
R
X
R
X
R
Table 33: Packet Status byte: bit description
Bit
Symbol
7 to 1
-
0
PacketOverwritten
Description
reserved
A logic 1 indicates that the previous packet was overwritten by a Setup Packet. In
that case the buffer is not cleared.
Table 34: Set Endpoint Status command: bit allocation
Bit
7
Symbol
Conditional
Stall
6
5
4
-
3
-
2
-
1
-
0
Rate
Feedback
Mode
0
W
Disable
Stalled
Reset
Access
0
W
0
W
X
W
X
W
X
W
X
W
0
W
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1130DL | Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1130N | Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1160 | Embedded Universal Serial Bus Host Controller |
| ISP1160BD | Embedded Universal Serial Bus Host Controller |
| ISP1160BM | Embedded Universal Serial Bus Host Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1130DL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1130N | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus compound hub with integrated keyboard controller |
| ISP1160 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD,157 | 功能描述:USB 接口集成電路 USB 1.1 HOST CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。