參數資料
型號： ISL6580CR
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Integrated Power Stage
中文描述： 35 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PQCC56
封裝： 8 X 8 MM, PLASTIC, QFN-56
文件頁數： 24/31頁
文件大?。?/td> 1391K
代理商： ISL6580CR
24
heat flux designed into the system is die and heat sink size.
The larger the die size, the higher the part costs but more
effective heat flux occurs. A smaller die size can be used
with a larger heat sink added. Of course increasing the
switching speed of the device and/or reducing the frequency
of operation of the transistor will reduce power dissipation,
but both of these are typically defined directly from the
application.
If there is a high thermal increase in a MOSFET, a cost
analysis should be performed to consider a larger die size, a
larger heat sink, or parallel MOSFETs to share the current.
MOSFET Transistor Selection
When selecting the appropriate low side MOSFET to put in
the power circuitry, there are some basic characteristics that
need to be considered.
N type or P type MOSFET
For the low side MOSFET component, an N polarity
MOSFET is always used.
Current Rating
At least 3X the peak current input should be select for the
current rating.
Voltage Rating
The input voltage for computing multiphase power supply for
the chip set is a 12V DC nominal. Standard MOSFET
voltage rating for the low side FET ranges between 20V-30V
depending on the switching speed of the switch node and
the noise of the input rail. This increased voltage level is
used to take into account inductive voltage kickback and
transient voltage inputs.
Inductive Switching
The ISL6580 Integrated Power Stage is a High Side
FET/driver combination with external synchronous rectifier
that provides high current at high switching frequency.
Schematic of Figure 38 shows a typical synchronous buck
converter application using the ISL6580.
Package and board level interconnects of individual
components in the high current loops give rise to series RLC
circuits. Fast switching of large currents in these loops will
generate large voltage transients that may exceed maximum
device ratings. Specifically, at the turn off phase of the high
side switch, the sudden disruption in the loop current will
generate fast transient ringing at the high side switch
exposing the high side switch to large voltages that can
exceed the rated break down voltage for that device. Figure
39 shows the high frequency equivalent circuit at the turn-off
of the high side switch before the turn-on of the low side
switch. Included in this schematic are the relevant parasitic
effects of various components and interconnects.
This application note discusses the use of external Schottky
diodes in order to limit the amplitude of transient voltage spikes
across the drain to source of the high side switch device.
Clamping Using Schottky Diodes
The simplest approach to protect the High Side FET from
inductive switching is to limit loop inductance. This can be
achieved by proper layout of the high current loops and
careful selection of the components in this loop. The goal is
to minimize overall loop inductance. This inductance
includes HSFET bonding inductance, the external NFET
inductance, the power supply decoupling capacitance’s ESL,
and interconnect inductances between these components.
While good layout of the PCB must be always practiced,
component selection is often compromised by other factors
such as pricing or physical dimensions. For example it is
possible that a single NFET with an inductance of up to 8nH
is selected for the low side switch.
In such situations where a high inductance FET or special
layout considerations result in large loop inductance, placement
of a Schottky diode from the switch node to ground will clamp
the negative ringing and limit the voltage across drain to source
FIGURE 38. SYNCHRONOUS BUCK CONVERTER USING
ISL6580
C
d s
C
g d
C
g s
R
N
L
N
C
d s
C
g d
C
g s
R
P
L
P
E S R
E S L
V
S U P P
R
i1
R
i2
R
i3
L
i1
L
i2
L
i3
I
L
R
i4
L
i4
L
H
C
S
FIGURE 39. HIGH FREQUENCY EQUIVALENT CIRCUIT OF
THE HIGH SIDE SWITCH TURN OFF LOOP
ISL6580
相關PDF資料
PDF描述
ISL6580CR-T Integrated Power Stage
ISL6590 Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-PDIP -40 to 85
ISL6590DR Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-PDIP -40 to 85
ISL6592DNZ-T FUSE, ANTISURGE 2A
ISL6592 Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-TSSOP -40 to 85
相關代理商/技術參數
參數描述
ISL6580CR-T 功能描述:IC DRIVER HIGH SIDE FET 56-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 內部開關 系列:- 標準包裝:1,000 系列:- 類型:高端/低端驅動器 輸入類型:SPI 輸出數:8 導通狀態電阻:850 毫歐，1.6 歐姆 電流 - 輸出 / 通道:205mA，410mA 電流 - 峰值輸出:500mA，1A 電源電壓:9 V ~ 16 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:PG-DSO-20-45 包裝:帶卷 (TR)
ISL6590DR-T 功能描述:IC REG CTRLR BST PWM VM 64-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF)
ISL6592DNZ-T 功能描述:IC DIGTL MULTIPHASE CTRLR 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
ISL6592DNZ-TR5196 功能描述:IC DIGTL MULTIPHASE CTRLR 48LQFP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR)
ISL6594ACB 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:50 系列:- 配置:低端 輸入類型:非反相 延遲時間:40ns 電流 - 峰:9A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:4.5 V ~ 35 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*