- 您現在的位置：買賣IC網 > PDF目錄9966 > IDT82P2828BH (IDT, Integrated Device Technology Inc)IC LIU T1/J1/E1 28+1CH 640-PBGA PDF資料下載
參數資料
| 型號： | IDT82P2828BH |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 88/154頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/J1/E1 28+1CH 640-PBGA |
| 標準包裝： | 5 |
| 類型： | 線路接口裝置（LIU） |
| 規程： | E1 |
| 電源電壓： | 3.13 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 640-BGA 裸露焊盤 |
| 供應商設備封裝： | 640-PBGA-EP（31x31） |
| 包裝： | 托盤 |
| 其它名稱： | 82P2828BH |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁
IDT82P2828
28(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Functional Description
39
February 6, 2009
3.3.5
LINE DRIVER
The Line Driver can be set to High-Z for protection or in redundant
applications.
The following two ways will set the Line Driver to High-Z:
Setting the OE pin to low will globally set all the Line Drivers to
High-Z;
Setting the OE bit (b6, TCF0,...) to ‘0’ will set the corresponding
Line Driver to High-Z.
By these ways, the functionality of the internal circuit is not affected
and TTIPn and TRINGn will enter High-Z state immediately.
3.3.5.1 Transmit Over Current Protection
The Line Driver monitors the Transmit Over Current (TOC) on the
line interface. When TOC is detected, the driver’s output (i.e., output on
TTIPn/TRINGn) is determined by the THZ_OC bit (b4, TCF0,...). If the
THZ_OC bit (b4, TCF0,...) is ‘0’, the driver’s output current (peak to
peak) is limited to 100 mA; if the THZ_OC bit (b4, TCF0,...) is ‘1’, the
driver’s output will enter High-Z. TOC is indicated by the TOC_S bit (b4,
STAT0,...). A transition from ‘0’ to ‘1’ on the TOC_S bit (b4, STAT0,...) or
any transition (from ‘0’ to ‘1’ or from ‘1’ to ‘0’) on the TOC_S bit (b4,
STAT0,...) will set the TOC_IS bit (b4, INTS0,...) to ‘1’, as selected by the
TOC_IES bit (b4, INTES,...). When the TOC_IS bit (b4, INTS0,...) is ‘1’,
an interrupt will be reported by INT if not masked by the TOC_IM bit (b4,
TOC may be indicated by the TMFn pin. Refer to Section 3.5.7.2
TMFn Indication for details.
3.3.6
TX TERMINATION
The transmit line interface supports Transmit Differential mode and
Transmit Single Ended mode, as selected by the T_SING bit (b3,
TCF0,...). In Transmit Differential mode, both TTIPn and TRINGn are
used to transmit signals to the line side. In Transmit Single Ended mode,
only TTIPn is used to transmit signal.
The line interface can be connected with T1 100
, J1 110 or E1
120
twisted pair cable or E1 75 coaxial cable.
The transmit impedance matching is realized by using internal
impedance matching or external impedance matching for each channel
in different applications.
3.3.6.1 Transmit Differential Mode
In Transmit Differential mode, different applications have different
impedance matching. For T1/J1 applications, only Internal Impedance
Matching is supported. For E1 applications, both Internal and External
Impedance Matching are supported.
Internal Impedance Matching circuit uses an internal programmable
resistor (IM) only.
External Impedance Matching circuit uses an external resistor (Rt)
only.
A twisted pair cable can be connected with a 1:2 (step up) trans-
former or without a transformer (transformer-less), while a coaxial cable
must be connected with a 1:2 transformer.
The T_TERM[2:0] bits (b2~0, TCF0,...) should be set according to
different cable conditions, whether a transformer is used, and what kind
of Impedance Matching is selected.
Table-15 lists the recommended impedance matching value in
one channel in different applications.
The transformer-less connection will offer a termination option with
reduced cost and board space. However, the waveform amplitude is not
standard compliant, and surge protection and common mode depres-
sion should be enhanced depending on equipment environment..
Table-15 Impedance Matching Value in Transmit Differential Mode
Cable Condition
Internal Impedance Matching
External Impedance Matching
T_TERM[2:0]
Rt
T_TERM[2:0]
Rt
T1 100
twisted pair (with transformer)
000
0
(not supported)
J1 110
twisted pair (with transformer)
001
E1 120
twisted pair (with transformer), PULS[3:0]=0001
010
111
10
E1 75
coaxial (with transformer), PULS[3:0]=0000
011
T1 100
twisted pair (transformer-less)
100
(not supported)
J1 110
twisted pair (transformer-less)
101
E1 120
twisted pair (transformer-less), PULS[3:0]=0001
110
相關PDF資料 |
PDF描述 |
|---|---|
| IDT723624L12PF | IC FIFO SYNC 256X36X2 128QFP |
| MS27473P22A35P | CONN PLUG 100POS STRAIGHT W/PINS |
| MS27499E14A5S | CONN RCPT 5POS BOX MNT W/SCKT |
| IDT723622L12PF | IC FIFO SYNC 256X36X2 120QFP |
| MAX1108CUB+ | IC ADC 8BIT LP 10-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P2828BHG | 功能描述:IC LIU T1/J1/E1 28+1CH 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| IDT82P2916 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel High-Density T1/E1/J1 Line Interface Unit |
| IDT82P2916BFG | 功能描述:IC LIU T1/E1/J1 16CH SH 484BGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:* |
| IDT82P2916BFG8 | 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P5088 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Universal Octal T1/E1/J1 LIU with Integrated Clock Adapter |
發布緊急采購，3分鐘左右您將得到回復。