- 您現在的位置：買賣IC網 > PDF目錄370657 > HPA00002DTR (Texas Instruments, Inc.) LOW POWER CURRENT MODE PUSH-PULL PWM PDF資料下載
參數資料
| 型號： | HPA00002DTR |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | LOW POWER CURRENT MODE PUSH-PULL PWM |
| 中文描述： | 低功耗電流模式推拉脈寬調制 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 174K |
| 代理商： | HPA00002DTR |
SLUS168D
–
APRIL 1999
–
REVISED AUGUST 2002
6
www.ti.com
pin descriptions (continued)
NOTE: The oscillator generates a sawtooth waveform on RC. During the RC rise time, the output stages alternate on time, but
both stages are off during the RC fall time. The output stages switch a the oscillator frequency, with guaranteed duty
cycle of < 50% for both outputs.
UDG
–
97009
Figure 1. Block Diagram for Oscillator
APPLICATION INFORMATION
A 200-kHz push-pull application circuit with a full wave rectifier is shown in Figure 2. The output, V
O
, provides 5 V
at 75 W maximum and is electrically isolated from the input. Since the UCC3808 is a peak current mode controller
the 2N2222A emitter following amplifier (buffers the CT waveform) provides slope compensation which is necessary
for duty ratios greater than 50%. Capacitor decoupling is very important with a single ground IC controller, and a 1
μ
F is suggested as close to the IC as possible. The controller supply is a series RC for start-up, paralleled with a bias
winding on the output inductor used in steady state operation.
Isolation is provided by an optocoupler with regulation done on the secondary side using the UC3965 Precision
Reference with Low Offset Error Amplifier. Small signal compensation with tight voltage regulation is achieved using
this part on the secondary side. Many choices exist for the output inductor depending on cost, volume, and
mechanicall strength. Several design options are iron powder, molypermalloy (MPP), or a ferrite core with an air gap
as shown here. The main power transformer is a low profile design, EFD size 25, using Magnetics Inc. P material
which is a good choice at this frequency and temperature. The input voltage may range from 36 V dc to 72 V dc.
相關PDF資料 |
PDF描述 |
|---|---|
| HPA00021DGGR | 14-BIT REGISTERED BUFFER WITH SSTL 2 INPUTS AND OUTPUTS |
| HPA00036DTR | Single Ended Active Clamp/Reset PWM |
| HPA00033DTR | Single Ended Active Clamp/Reset PWM |
| HPA00034DTR | Single Ended Active Clamp/Reset PWM |
| HPA00035DTR | Single Ended Active Clamp/Reset PWM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HPA00021DGGR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:14-BIT REGISTERED BUFFER WITH SSTL 2 INPUTS AND OUTPUTS |
| HPA00033DTR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single Ended Active Clamp/Reset PWM |
| HPA00034DTR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single Ended Active Clamp/Reset PWM |
| HPA00035DTR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single Ended Active Clamp/Reset PWM |
| HPA00036DTR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Single Ended Active Clamp/Reset PWM |
發布緊急采購，3分鐘左右您將得到回復。