- 您現在的位置：買賣IC網 > PDF目錄223866 > GS8662T06BD-350I (GSI TECHNOLOGY) 8M X 8 DDR SRAM, 0.45 ns, PBGA165 PDF資料下載
參數資料
| 型號： | GS8662T06BD-350I |
| 廠商： | GSI TECHNOLOGY |
| 元件分類： | SRAM |
| 英文描述： | 8M X 8 DDR SRAM, 0.45 ns, PBGA165 |
| 封裝： | 13 X 15 MM, 1 MM PITCH, FPBGA-165 |
| 文件頁數： | 32/33頁 |
| 文件大小： | 651K |
| 代理商： | GS8662T06BD-350I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.02 3/2011
8/33
2011, GSI Technology
GS8662T20/38BD-550/500/450/400/350
GS8662T06/11BD-500/450/400/350
Power-Up Sequence for SigmaDDR-II+ SRAMs
For compatibility across all vendors it is recommended that SigmaDDR-II+ SRAMs must be powered-up in a specific sequence in
order to avoid undefined operations.
Power-Up Sequence
1. Power-up and maintain Doff at Low state.
1a. Apply VDD.
1b. Apply VDDQ.
1c. Apply VREF (may also be applied at the same time as VDDQ).
2. After voltages are within specification range, and clocks (K, K) are stablized, change Doff to High.
3. An additional 2048 clock cycles are required to lock the DLL after it has been enabled.
Note: The DLL may be reset by driving the Doff pin Low or by stopping the K clocks for at least 30 ns. 2048 cycles of clean K
clocks are always required to relock the DLL after it has been stabilized.
DLL Constraints
The DLL synchronizes to either K clock. These clocks should have low phase jitter (tKVar).
The DLL cannot operate at a frequency lower than that specified by the tKHKH maximum specification for the desired
operating clock frequency.
If the incoming clock is not stablized when DLL is enabled, the DLL may lock on the wrong frequency and cause
undefined errors or failures during the initial stage.
Special Functions
Byte Write and Nybble Write Control
Byte Write Enable pins are sampled at the same time that Data In is sampled. A high on the Byte Write Enable pin associated with
a particular byte (e.g., BW0 controls D0–D8 inputs) will inhibit the storage of that particular byte, leaving whatever data may be
stored at the current address at that byte location undisturbed. Any or all of the Byte Write Enable pins may be driven High or Low
during the data in sample times in a write sequence.
Each write enable command and write address loaded into the RAM provides the base address for a 2-beat data transfer. The x18
version of the RAM, for example, may write 36 bits in association with each address loaded. Any 9-bit byte may be masked in any
write sequence.
Nybble Write (4-bit) control is implemented on the 8-bit-wide version of the device. For the x8 version of the device, “Nybble
Write Enable” and “NWx” may be substituted in all the discussion above.
Example x18 RAM Write Sequence using Byte Write Enables
Data In Sample Time
BW0
BW1
D0–D8
D9–D17
Beat 1
0
1
Data In
Don’t Care
Beat 2
1
0
Don’t Care
Data In
Resulting Write Operation
Byte 1
D0–D8
Byte 2
D9–D17
Byte 3
D0–D8
Byte 4
D9–D17
Written
Unchanged
Written
Beat 1
Beat 2
相關PDF資料 |
PDF描述 |
|---|---|
| GS8662T06BD-350T | 8M X 8 DDR SRAM, 0.45 ns, PBGA165 |
| GS8672Q38BE-500I | 2M X 36 QDR SRAM, 0.45 ns, PBGA165 |
| GS880F32AGT-5.5IT | 256K X 32 CACHE SRAM, 5.5 ns, PQFP100 |
| GS880F32BGT-7IT | 256K X 32 CACHE SRAM, 7 ns, PQFP100 |
| GSAA07C-Q01 | SNAP ACTING/LIMIT SWITCH, SPDT, MOMENTARY, 0.1A, 50VDC, PANEL MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS8662T06BD-450 | 制造商:GSI Technology 功能描述:GS8662T06BD-450 - Trays |
| GS8662T06BD-500 | 制造商:GSI Technology 功能描述:GS8662T06BD-500 - Trays |
| GS8662T06BD-550 | 制造商:GSI Technology 功能描述:GS8662T06BD-550 - Trays |
| GS8662T07BD-450 | 制造商:GSI Technology 功能描述:165 FBGA - Bulk |
| GS8662T08BD-400 | 制造商:GSI Technology 功能描述:165 FBGA - Bulk |
發布緊急采購，3分鐘左右您將得到回復。