- 您現在的位置：買賣IC網 > PDF目錄17031 > EVAL-AD7264EDZ (Analog Devices Inc)BOARD EVALUATION FOR AD7264 PDF資料下載
參數資料
| 型號： | EVAL-AD7264EDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7264 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 1M |
| 數據接口： | 串行 |
| 輸入范圍： | 5 Vpp |
| 在以下條件下的電源（標準）： | 120mW @ 1MSPS |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7264 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Data Sheet
AD7264
Rev. B | Page 27 of 28
APPLICATION HINTS
GROUNDING AND LAYOUT
The analog and digital supplies to the AD7264 are independent
and separately pinned out to minimize coupling between the
analog and digital sections of the device. The printed circuit
board (PCB) that houses the AD7264 should be designed so
that the analog and digital sections are separated and confined
to certain areas of the board. This design facilitates the use of
ground planes that can be easily separated.
To provide optimum shielding for ground planes, a minimum
etch technique is generally best. All five AGND pins of the AD7264
should be sunk in the AGND plane. Digital and analog ground
planes should be joined in only one place. If the AD7264 is in a
system where multiple devices require an AGND to DGND
connection, the connection should still be made at only one point,
a star ground point, that should be established as close as possible
to the ground pins on the AD7264.
Avoid running digital lines under the device because this couples
noise onto the die. However, the analog ground plane should be
allowed to run under the AD7264 to avoid noise coupling. The
power supply lines to the AD7264 should use as large a trace as
possible to provide low impedance paths and reduce the effects
of glitches on the power supply line.
To avoid radiating noise to other sections of the board, fast
switching signals, such as clocks, should be shielded with digital
ground, and clock signals should never run near the analog inputs.
Avoid crossover of digital and analog signals. To reduce the effects
of feedthrough within the board, traces on opposite sides of the
board should run at right angles to each other. A microstrip
technique is the best method but is not always possible with a
double-sided board. In this technique, the component side of
the board is dedicated to ground planes, while signals are placed
on the solder side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 μF tantalum capacitors in parallel with
100 nF capacitors to GND. To achieve the best results from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 μF capacitors should have low effective series resistance
(ESR) and low effective series inductance (ESI), such as the
common ceramic types or surface-mount types. These low ESR
and low ESI capacitors provide a low impedance path to ground
at high frequencies to handle transient currents due to internal
logic switching.
PCB DESIGN GUIDELINES FOR LFCSP
The lands on the chip scale package (CP-48-1) are rectangular.
The PCB pad for these should be 0.1 mm longer than the package
land length, and 0.05 mm wider than the package land width,
leaving a portion of the pad exposed. To ensure that the solder
joint size is maximized, the land should be centered on the pad.
The bottom of the chip scale package has a thermal pad. The
thermal pad on the PCB should be at least as large as the exposed
pad. On the PCB, there should be a clearance of at least 0.25 mm
between the thermal pad and the inner edges of the pad pattern
to ensure that shorting is avoided.
To improve thermal performance of the package, use thermal vias
on the PCB, incorporating them in the thermal pad at 1.2 mm
pitch grid. The via diameter should be between 0.3 mm and
0.33 mm, and the via barrel should be plated with 1 oz copper
to plug the via. The user should connect the PCB thermal pad
to AGND.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7939CBZ | BOARD EVALUATION FOR AD7939CBZ |
| PCMC135T-1R5MF | COIL 1.5 UH POWER CHOKE 20% SMD |
| VI-B5J-EY | CONVERTER MOD DC/DC 36V 50W |
| TFL0816-12N | INDUCTOR 12NH +/-2% 0603 |
| EVAL-AD7722CBZ | BOARD EVALUATION FOR AD7722CBZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7265CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
| EVAL-AD7265CB1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
| EVAL-AD7265EDZ | 功能描述:BOARD EVAL FOR AD7265 A/D CONV RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7266CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD7266CB1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential Input, Dual 2 MSPS, 12-Bit, 3-Channel SAR ADC |
發布緊急采購，3分鐘左右您將得到回復。