參數資料
型號: DS2490S
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: Bus Controller
英文描述: UNIVERSAL SERIAL BUS CONTROLLER, PDSO24
封裝: 0.300 INCH, SO-24
文件頁數: 23/51頁
文件大?。?/td> 444K
代理商: DS2490S
DS2490
3 of 50
SECTION
SUMMARY
SUSPEND OUTPUT
SUSO
signal operation and purpose
ELECTRICAL CHARACTERISTICS
DC and AC specifications
APPLICATION INFORMATION
HW application example
APPENDIX 1
CONTROL COMMANDS—USB setup packet encoding
APPENDIX 2
COMMUNICATION COMMANDS—USB setup packet
encoding
APPENDIX 3
MODE COMMANDS—USB setup packet encoding
APPENDIX 4
USB command and command type constant codes
OVERVIEW
The DS2490 directly interfaces a USB port to a 1-Wire bus. As shown in Figure 1, the DS2490
incorporates a USB physical interface, a USB device controller coupled with a 1-Wire-specific USB
function core, and a 1-Wire bus interface controller. The 1-Wire interface controller shapes the slopes of
the 1-Wire waveforms, applies programming pulses or strong pullup to 5V, and reads the 1-Wire bus
using a non-TTL threshold to maximize the noise margin for best performance on large 1-Wire Networks.
1-Wire waveform timing is accurately controlled with a crystal-based oscillator.
The DS2490 also supports USB remote wake-up which enables the DS2490-based USB peripheral to
send resume signaling to a suspended host system. If the remote wake-up function is enabled and the host
system is in a suspended state, a 1-Wire device attachment will cause the DS2490 to perform a host
system wake-up and allow the 1-Wire device to be serviced.
DS2490 FUNCTIONAL BLOCK DIAGRAM Figure 1
USB
XCVR
USB
DEVICE
CONTROLLER
PWR
CNTL
USB
1-WIRE
FUNCTION
CORE
EP
FIFOS
OSC
CLK
GEN
USB
DESC
ROM
1-WIRE
I/F
CONTROLLER
1-WIRE
XI
VPP
XO
D+
D-
VB
VD
GND
SUSO
Typical application examples of the DS2490 are shown in Figure 2 (a to c). As shown in all the examples,
all host control and communication with the device is accomplished over a USB communication link. A
USB vendor-specific command set, as defined in this document, is used to select operational modes
(MODE COMMANDS), control command processing (CONTROL COMMANDS), and communicate
over the 1-Wire interface (COMMUNICATION COMMANDS). Shown in Figure 2, example (a) is a
DS2490-based USB peripheral application. The peripheral function is a USB to 1-Wire adapter and
provides both USB and 1-Wire I/O connections. In this example, the peripheral is attached to the USB
enabled host computer either directly at a root port or through a USB hub. The 1-Wire bus interface
相關PDF資料
PDF描述
DS2502P 128 X 8 OTPROM, PDSO6
DS2502S 128 X 8 OTPROM, PDSO8
DS2502 128 X 8 OTPROM, PBCY3
DS2505/T&R 16K X 1 OTPROM, PBCY3
DS2505P 16K X 1 OTPROM, PDSO6
相關代理商/技術參數
參數描述
DS2490S+ 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Rail/Tube 制造商:Maxim Integrated Products 功能描述:USB 1-W BRIDGE CHIP 24-SO LF 制造商:Maxim Integrated Products 功能描述:Bulk
DS2490S+T&R 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Tape and Reel
DS2490S+TR 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:USB to 1-Wire Bridge Chip
DS2490X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:USB to 1-Wire Bridge Chip(468.41 k)
DS2490X/T&R 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59