- 您現在的位置：買賣IC網 > PDF目錄10656 > DS2480B+T&R (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8SOIC PDF資料下載
參數資料
| 型號： | DS2480B+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8SOIC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | DS2480B+T&RDKR |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2480B
Maxim Integrated........................................................................................................................................................................................... 15
Falling Edges (DS2480B-initiated)
Whenever the DS2480B begins pulling the 1-Wire bus low to initiate a time slot, for example, it first
turns off the weak pullup current IWEAKPU. Then, at standard and Overdrive speeds it will generate a
falling edge at a slew rate of typically 15V/s. This value is acceptable for short 1-Wire busses and
adequate for communication at Overdrive speed. For 1-Wire networks of more than roughly 30m length
one should always use flexible speed. One of the parameters that is adjustable at flexible speed is the slew
rate of DS2480B-initiated falling edges. The effect of the slew rate control is shown in Figure 5.
Figure 5. SLEW RATE CONTROL
As extensive tests have shown, 1-Wire networks at a length of up to 300m will perform best if the fall
time tF is in the range of 4 ± 0.5s. This translates into a slew rate of approximately 1V/s. This slew rate
is typically achieved by setting the configuration parameter 001 (Pulldown Slew Rate Control) to a value
of 100 (see Table 4). If the actual measured fall time is longer than the target value, one should use a
value code of 011 or lower. If the fall time is shorter, one should use a value code of 101 or higher.
Once determined, the value code for the Pulldown Slew Rate Control parameter should be stored in the
host and always be loaded into the DS2480B after a power-on or master reset cycle.
TIMING DIAGRAMS
This section explains the waveforms generated by the DS2480B on the 1-Wire bus in detail. First the
communication waveforms such as the Reset/Presence Detect Sequence and the time slots are discussed.
After that follows a detailed description of the pulse function under various conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX967ESA+T | IC COMPARATOR R-R 8-SOIC |
| AD774BKNZ | IC ADC 12BIT W/BUFF REF 28DIP |
| MAX967EUA+T | IC COMPARATOR R-R 8-UMAX |
| LTC1608ACG#PBF | IC A/D CONV 16BIT SAMPLNG 36SSOP |
| MAX932CUA+T | IC COMPARATOR W/REF 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2480S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial 1.Wire Line Driver |
| DS2482-100 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482-100_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master |
| DS2482-101 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
| DS2482-101_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
發布緊急采購，3分鐘左右您將得到回復。