- 您現在的位置：買賣IC網 > PDF目錄10656 > DS2480B+T&R (Maxim Integrated Products)IC LINE DRVR W/SENSOR 1-W 8SOIC PDF資料下載
參數資料
| 型號： | DS2480B+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/32頁 |
| 文件大小： | 0K |
| 描述： | IC LINE DRVR W/SENSOR 1-W 8SOIC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
| 其它名稱： | DS2480B+T&RDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
DS2480B
Maxim Integrated........................................................................................................................................................................................... 20
PULSE WAVEFORM, ARMED
As explained in the Communication Commands section, bit 1 of the Pulse command allows the arming of
a strong pullup to 5V if the bit is set to 1. If the strong pullup is armed and the device is switched to Data
Mode, there will be a strong pullup immediately following every byte on the 1-Wire bus. This mode is
implemented to provide extra energy when writing to EEPROM devices or to do a temperature
conversion with the DS1920 temperature iButton, for example. These devices need a strong pullup
immediately after the power-consuming activity has been initiated by a command code.
To arm the strong pullup, one usually generates a “dummy” pulse with bit 1 being 1 while the device is in
Command Mode. To save time, the dummy pulse may immediately be terminated by sending the
Termination command, code F1h. Then one switches to Data Mode and sends a command code that
makes one or more slaves on the 1-Wire bus require extra energy. After the command execution is
finished, one switches back to Command Mode and disarms the strong pullup by generating another
dummy pulse. A complete temperature conversion sequence that shows the use of the armed pulse is
included in the Software Driver Examples section .
Figure 8. STRONG PULLUP TO 5V, ARMED, PREDEFINED DURATION
Figures 8 shows the timing of the strong pullup in Data Mode. At t1 the 8th time slot of the byte sent to the
1-Wire bus is completed. Without any delay the DS2480B now activates the strong pullup and
simultaneously starts sending the data response byte to the host. At t2 the strong pullup ends and the
DS2480B sends a pulse response byte to the host. The idle time between t2 and t3 is comprised of the time
to transmit the pulse response byte, plus the response time of the host plus the time to transmit the
command and/or data to generate the next time slot. Since in Data Mode the Pulse Termination command
is not applicable, the duration of the strong pullup must be limited. See Table 4, parameter 011 (Strong
Pullup Duration) for details.
Infinite duration, if accidentally selected, will require a power-on or master reset cycle to get the
DS2480B back to communicating with the host.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX967ESA+T | IC COMPARATOR R-R 8-SOIC |
| AD774BKNZ | IC ADC 12BIT W/BUFF REF 28DIP |
| MAX967EUA+T | IC COMPARATOR R-R 8-UMAX |
| LTC1608ACG#PBF | IC A/D CONV 16BIT SAMPLNG 36SSOP |
| MAX932CUA+T | IC COMPARATOR W/REF 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2480S | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Serial 1.Wire Line Driver |
| DS2482-100 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Single-Channel 1-Wire Master |
| DS2482-100_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master |
| DS2482-101 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
| DS2482-101_12 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Sleep Mode |
發布緊急采購，3分鐘左右您將得到回復。