參數資料
型號： DS21Q44T+
廠商： Maxim Integrated Products
文件頁數： 17/105頁
文件大?。?/td> 0K
描述： IC FRAMER ENHANCED E1 4X 128TQFP
標準包裝： 72
控制器類型： E1 調幀器
接口： 并行/串行
電源電壓： 2.97 V ~ 3.63 V
電流 - 電源： 75mA
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 128-LQFP
供應商設備封裝： 128-LQFP（14x20）
包裝： 管件
DS21Q44
19 of 105
Signal Name:
BTS
Signal Description:
Bus Type Select
Signal Type:
Input
Strap high to select Motorola bus timing; strap low to select Intel bus timing. This pin controls the
function of the RD*(DS*), ALE(AS), and WR*(R/W*) pins. If BTS = 1, then these pins assume the
function listed in parenthesis ().
Signal Name:
RD* (DS*)
Signal Description:
Read Input (Data Strobe)
Signal Type:
Input
RD* and DS* are active low signals. Note: DS is active high when MUX=1. Refer to bus timing
diagrams in section 19 .
Signal Name:
FS0 AND FS1
Signal Description:
Framer Selects
Signal Type:
Input
Selects which of the four framers to be accessed.
Signal Name:
CS*
Signal Description:
Chip Select
Signal Type:
Input
Must be low to read or write to the device. CS* is an active low signal.
Signal Name:
WR* (R/W*)
Signal Description:
Write Input (Read/Write)
Signal Type:
Input
WR* is an active low signal.
TEST ACCESS PORT PINS
Signal Name:
TEST
Signal Description:
3–State Control
Signal Type:
Input
Set high to 3–state all output and I/O pins (including the parallel control port). Set low for normal
operation. Useful in board level testing.
Signal Name:
JTRST
Signal Description:
IEEE 1149.1 Test Reset
Signal Type:
Input
If FMS = 1: JTAG functionality is not available and JTRST is held LOW internally.
If FMS = 0: JTAG functionality is available and JTRST is pulled up internally by a 10=kilo ohm resistor.
If FMS = 0, and boundary scan is not used this pin should be held low. This signal is used to
asynchronously reset the test access port controller. The device enters the DEVICE ID MODE when
JTRST is pulled high. The device enters the DEVICE ID MODE when JTRST is pulled high. The
device operates as a T1/E1 transceiver if JTRST is pulled low.
相關PDF資料
PDF描述
DS21Q50LN IC TRANSCEIVER E1 QD IND 100LQFP
DS21Q55 IC TXRX QUAD T1/E1/J1 SCT 256BGA
DS21Q59LN+ IC TXRX E1 QUAD 100-LQFP
DS21S07AS+T&R IC TERMINATOR SCSI 16-SOIC
DS21T05Z/T&R IC TERMINATOR SCSI 150MIL 16SOIC
相關代理商/技術參數
參數描述
DS21Q44T+ 功能描述:網絡控制器與處理器 IC Enhanced Quad E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q44TN 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q48 功能描述:網絡控制器與處理器 IC 5V Quad E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q48A3N 功能描述:網絡控制器與處理器 IC 5V Quad E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q48B 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*