- 您現在的位置：買賣IC網 > PDF目錄1914 > DS21FT44N+ (Maxim Integrated Products)IC FRAMER 4X4 16CH 300-BGA PDF資料下載
參數資料
| 型號： | DS21FT44N+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 98/117頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FRAMER 4X4 16CH 300-BGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 40 |
| 控制器類型： | E1 調幀器 |
| 接口： | 并行/串行 |
| 電源電壓： | 2.97 V ~ 3.63 V |
| 電流 - 電源： | 225mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 300-BBGA |
| 供應商設備封裝： | 300-PBGA（27x27） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁當前第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
DS21FT44/DS21FF44
81 of 117
TDC2: TRANSMIT HDLC DS0 CONTROL REGISTER 2 (Address = BB Hex)
(MSB)
(LSB)
TDB8
TDB7
TDB6
TDB5
TDB4
TDB3
TDB2
TDB1
SYMBOL
POSITION
NAME AND DESCRIPTION
TDB8
TDC2.7
DS0 Bit 8 Suppress Enable. MSB of the DS0. Set to one to
stop this bit from being used.
TDB7
TDC2.6
DS0 Bit 7 Suppress Enable. Set to one to stop this bit from
being used.
TDB6
TDC2.5
DS0 Bit 6 Suppress Enable. Set to one to stop this bit from
being used.
TDB5
TDC2.4
DS0 Bit 5 Suppress Enable. Set to one to stop this bit from
being used.
TDB4
TDC2.3
DS0 Bit 4 Suppress Enable. Set to one to stop this bit from
being used.
TDB3
TDC2.2
DS0 Bit 3 Suppress Enable. Set to one to stop this bit from
being used.
TDB2
TDC2.1
DS0 Bit 2 Suppress Enable. Set to one to stop this bit from
being used.
TDB1
TDC2.0
DS0 Bit 1 Suppress Enable. LSB of the DS0. Set to one to
stop this bit from being used.
20.
INTERLEAVED PCM BUS OPERATION
In many architectures, the outputs of individual framers are combined into higher speed serial buses to
simplify transport across the system. The DS21Q44 can be configured to allow each framer’s data and
signaling busses to be multiplexed into higher speed data and signaling busses eliminating external
hardware saving board space and cost.
The interleaved PCM bus option supports two bus speeds and interleave modes. The 4.096MHz bus
speed allows two framers to share a common bus. The 8.192MHz bus speed allows all four of the
DS21Q44’s framers to share a common bus. Framers can interleave their data either on byte or frame
boundaries. Framers that share a common bus must be configured through software and require several
device pins to be connected together externally (Figures 20-1 and 20-2). Each framer’s elastic stores must
be enabled and configured for 2.048MHz operation. The signal RSYNC must be configured as an input
on each framer.
For all bus configurations, one framer will be configured as the master device and the remaining framers
on the shared bus will be configured as slave devices. Refer to the IBO register description below for
more detail. In the 4.096MHz bus configuration there is one master and one slave per bus. Figure 20-1
shows the DS21Q44 configured to support two 4.096 MHz buses. Bus 1 consists of framers 0 and 1. Bus
2 consists of framers 2 and 3. Framers 0 and 2 are programmed as master devices. Framers 1 and 3 are
programmed as slave devices. In the 8.192 MHz bus configuration there is one master and three slaves.
Figure 20-2 shows the DS21Q44 configured to support an 8.192MHz bus. Framer 0 is programmed as the
master device. Framers 1, 2, and 3 are programmed as slave devices. Consult timing diagrams in section
22 for additional information.
When using the frame interleave mode, all framers that share an interleaved bus must have receive signals
(RPOS and RNEG) that are synchronous with each other. The received signals must originate from the
same clock reference. This restriction does not apply in the byte interleave mode.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21Q352B | IC TXRX QUAD T1/E1 3.3V 256-BGA |
| DS21Q41BT | IC FRAMER T1 QUAD 128-TQFP |
| DS21Q42T+ | IC FRAMER ENHANCED T1 4X 128TQFP |
| DS21Q43-ATN | IC FRAMER E1 QUAD 5V 128-TQFP |
| DS21Q44T+ | IC FRAMER ENHANCED E1 4X 128TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21FT44N+ | 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q348 | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q348B | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q348DK | 功能描述:網絡開發工具 RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS21Q348N | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。