- 您現在的位置：買賣IC網 > PDF目錄17127 > DEMOMPR083 (Freescale Semiconductor)BOARD DEMO FOR MPR083 CTLR PDF資料下載
參數資料
| 型號： | DEMOMPR083 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 7/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DEMO FOR MPR083 CTLR |
| 產品培訓模塊： | Sensor Toolbox |
| 標準包裝： | 1 |
| 傳感器類型： | 觸摸，電容式 |
| 傳感范圍： | 8 個按鈕/鍵 |
| 接口： | I²C |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，電池 |
| 已用 IC / 零件： | MPR083 |
| 產品目錄頁面： | 2808 (CN2011-ZH PDF) |
| 相關產品： | MPR083EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR083QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR083Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR083EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR083EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
MPR083
Sensors
Freescale Semiconductor
15
5
Low Power Configuration
5.1
Introduction
The MPR083 features a Low Power mode that can reduce the power consumption into the microamps range. This feature can
be used to both adjust the response time of the system, and change the conditions on which Low Power would be enabled.
5.2
Operation
This Low Power configuration is only active when the sensor controller is in Run2 mode. The Low Power mode decreases current
consumption by increasing the response time of the MPR083. This increase is controlled through two factors.
During normal Run2 operation of the sensor controller the Max Response Time (MRT) is calculated by taking the product of the
TASP and the primary clock. From Chapter 4 the primary clock is the (MTP + 5) ms. Since the sensor controller is in Run2, the
primary clock is also multiplied by a factor of 8. The debounce rate of the MPR083 is 4 times the sample rate thus the MRT is
represented by the following equation.
Equation 1
First, the Idle Interface Timeout (IIT) represents the total time the touch interface should remain idle before going into Low Power
mode. This value can be calculated by taking the product of the ITP, TASP and primary clock (8ms) with a factor of 64. Thus the
IIT is represented as follows:
Equation 2
Second, the Max Response Time (MRT) represents the total time the touch interface should remain inactive before scanning the
electrodes. This value can be calculated by taking the product of the SCD, TASP and primary clock (8ms) with a factor of 5. Thus
the MRT is represented as follows:
Equation 3
When in Run2 mode, the sensor controller will initially scan the electrodes at the rate of MRT1. When scanning at MRT1 and the
touch interface remains idle for the IIT period then the scan period will change to MRT2. When scanning at MRT2 and a touch is
detected the scan rate will transition back to MRT1.
Figure 18. Low Power Scan Period Transition Diagram
MRT1
MTP
5
+
8
----------------------
1
+
TASP
48ms
=
MRT2
MTP
5
+
8
----------------------
1
+
TASP
SCD
48
ms
=
ITT
MTP
5
+
8
----------------------
1
+
TASP
ITP
68ms
=
LP DISABLED
ITT PERIOD
run2 SET
TOUCH DETECTED
MRT1
MRT2
相關PDF資料 |
PDF描述 |
|---|---|
| 0210390880 | CABLE JUMPER 1MM .076M 19POS |
| EEM28DTBI | CONN EDGECARD 56POS R/A .156 SLD |
| ADR02ARZ-REEL | IC VREF SERIES PREC 5V 8-SOIC |
| EA-OEM-410 | KIT LPC3250 259 WITH QVGA |
| VI-J7P-EZ | CONVERTER MOD DC/DC 13.8V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DEMO-MSA | 制造商:Avago Technologies 功能描述:DEMOBOARD MSA-XX05,10,11,36,70,86 - Bulk |
| DEMONB5CP1V1 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO |
| DEMO-NB5CP1V1 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB5 CP1 PLC Sales Demo |
| DEMO-NB7CP1V1 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB7 CP1 PLC Sales Demo |
| DEMO-NJ51-KIT-ECT-0-V1 | 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NJ5 Demo UGKIT, TJG5ML2 to NJE |
發布緊急采購，3分鐘左右您將得到回復。