參數資料
型號： DEMOMPR083
廠商： Freescale Semiconductor
文件頁數： 31/35頁
文件大小： 0K
描述： BOARD DEMO FOR MPR083 CTLR
產品培訓模塊： Sensor Toolbox
標準包裝： 1
傳感器類型： 觸摸，電容式
傳感范圍： 8 個按鈕/鍵
接口： I²C
電源電壓： 1.8 V ~ 3.6 V
嵌入式： 是，MCU，8 位
已供物品： 板，電池
已用 IC / 零件： MPR083
產品目錄頁面： 2808 (CN2011-ZH PDF)
相關產品： MPR083EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR083Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR083EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083
Sensors
Freescale Semiconductor
5
The remaining 5 connections are SCL, SDA, IRQ, ATTN, and SOUNDER. Depending on the specific application, each of these
control lines can be used by connecting them to a host system. In the most minimal system, the SCL and SDA must be connected
to a master I2C interface to communicate with the MPR083. All of the connections for the MPR083 are shown by the schematic
Figure 4. Recommended System Connections Schematic
Note that in this configuration the AD0 address line is tied high thus the slave address of the MPR083 0x4D. Alternatively the
address line can be pulled low if the host system needs the MPR083 to be on address 0x4C. This functionality can also be used
to incorporate two MPR083 devices in the same system.
2.3
Serial Interface
The MPR083 uses an I2C Serial Interface. The I2C protocol implementation and the specifics of communicating with the Touch
Sensor Controller are detailed in the following sections.
2.3.1
Serial-Addressing
The MPR083 operates as a slave that sends and receives data through an I2C 2-wire interface. The interface uses a serial data
line (SDA) and a serial clock line (SCL) to achieve bi-directional communication between master(s) and slave(s). A master
(typically a microcontroller) initiates all data transfers to and from the MPR083, and generates the SCL clock that synchronizes
the data transfer.
The MPR083 SDA line operates as both an input and an open-drain output. A pull-up resistor, typically 4.7k
, is required on SDA.
The MPR083 SCL line operates only as an input. A pull-up resistor, typically 4.7k
, is required on SCL if there are multiple
masters on the 2-wire interface, or if the master in a single-master system has an open-drain SCL output.
Each transmission consists of a START condition (Figure 5) sent by a master, followed by the MPR083’s 7-bit slave address plus
R/W bit, a register address byte, one or more data bytes, and finally a STOP condition.
Figure 5. Wire Serial Interface Timing Details
E1
E2
E3
E4
E5
E6
E7
E8
VDD
VSS
SCL
SDA
AD0
SOUNDER
ATTN
IRQ
1
4
3
2
5
8
7
6
16
13
14
15
12
9
10
11
780k
Ω
1
4
3
2
5
8
7
6
E1
E2
E3
E4
E5
E6
E7
E8
9 GND
GND
MPR083
SCL
SDA
SOUNDER
ATTN
IRQ
8-POSITION
ROTARY
ELECTRODE
ARRAY
780k
Ω 780kΩ 780kΩ 780kΩ
780k
Ω 780kΩ 780kΩ
GND
1μF
VDD
4.7k
Ω
VDD
SCL
SDA
tLOW
tHIGH
tF
tR
tHD STA
tHD DAT
tHD STA
tSU DAT
tSU STA
tBUF
tSU STO
START
CONDITION
STOP
CONDITION
REPEATED START
CONDITION
START
CONDITION
相關PDF資料
PDF描述
0210390880 CABLE JUMPER 1MM .076M 19POS
EEM28DTBI CONN EDGECARD 56POS R/A .156 SLD
ADR02ARZ-REEL IC VREF SERIES PREC 5V 8-SOIC
EA-OEM-410 KIT LPC3250 259 WITH QVGA
VI-J7P-EZ CONVERTER MOD DC/DC 13.8V 25W
相關代理商/技術參數
參數描述
DEMO-MSA 制造商:Avago Technologies 功能描述:DEMOBOARD MSA-XX05,10,11,36,70,86 - Bulk
DEMONB5CP1V1 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO
DEMO-NB5CP1V1 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB5 CP1 PLC Sales Demo
DEMO-NB7CP1V1 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB7 CP1 PLC Sales Demo
DEMO-NJ51-KIT-ECT-0-V1 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NJ5 Demo UGKIT, TJG5ML2 to NJE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*