參數資料
型號： DEMOMPR083
廠商： Freescale Semiconductor
文件頁數： 5/35頁
文件大?。?/td> 0K
描述： BOARD DEMO FOR MPR083 CTLR
產品培訓模塊： Sensor Toolbox
標準包裝： 1
傳感器類型： 觸摸，電容式
傳感范圍： 8 個按鈕/鍵
接口： I²C
電源電壓： 1.8 V ~ 3.6 V
嵌入式： 是，MCU，8 位
已供物品： 板，電池
已用 IC / 零件： MPR083
產品目錄頁面： 2808 (CN2011-ZH PDF)
相關產品： MPR083EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR083Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR083EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083
Sensors
Freescale Semiconductor
13
4.3
Run1 Mode
When in Run1 mode the sensor controller will run continuously. During Run1 all the modules are synchronized by the Master Tick
Period. This value can be set by using the Master Tick Period Register as outlined in the following section.
While in this mode all functionality of the MPR083 is enabled; touch detection will occur, and I2C communication will be available.
This mode is enabled by setting the Configuration Register’s RUNE and DCE bits high.
4.3.1
Master Tick Period Register
The Master Tick Period Register is used to set the master tick of this system. All parts of the system are synchronized to this
counter. This register is overridden in all modes except for Run1. When not in Run1 mode, the value of this register is ignored
and 8ms is used for the primary clock. The I2C slave address of the Master Tick Period Register is 0x05.
Figure 16. Master Tick Period Register
4.4
Run2 Mode
When in Run2 mode the sensor controller will continue to scan the electrodes but a low power state will be enabled between
each cycle. Because of this, any I2C communication that occurs, may or may not respond while the sensor is in this mode.
If DCE is enabled the sensor controller transitions between low power and active states. During the active part of the cycle
communication with the sensor controller is possible; however, Freescale always requires users to issue an ATTN signal prior to
initiating communications. Accessing the I2C interface while DCE mode is enabled without sending an ATTN signal first is likely
to produce invalid data.
This mode is enabled by setting the Configuration Register’s RUNE bit high and DCE bit low. The only way to exit this mode is
to toggle the Attention Pin, refer to Section 4.7.
4.5
Stop1 Mode
When in Stop1 mode the sensor controller will not scan the electrodes. While capacitance sensing is disabled I2C
communications will still be accepted and the sensor controller will maintain instantaneous response to all register requests. This
is the only mode in which register values can be set.
This mode is enabled by setting the Configuration Register’s RUNE bit low and DCE bit high.
4.6
Stop2 Mode
When in Stop2 mode the sensor controller will not scan the electrodes or accept I2C communication. The MPR083 is off during
this mode.
This mode is enabled by setting the Configuration Register’s RUNE bit low and DCE bit low. The only way to exit this mode is to
toggle the Attention Pin, refer to Section 4.7.
7
6
543210
R
MTP
W
Reset:
0
000101
= Unimplemented
Table 9. Master Tick Period Register Field Descriptions
Field
Description
7:0
MTP
Master Tick Period – The Master Tick Period selects or reports the current value of the
touch sensor controller’s primary clock multiplier. The resulting period must be in the
range 5ms to 31ms. If the value is outside of this range the MTP will be set to 00011010.
00000000 Encoding 0 – Sets the primary clock multiplier to 5
~
00011010 Encoding 26 - Sets the primary clock multiplier to 31
相關PDF資料
PDF描述
0210390880 CABLE JUMPER 1MM .076M 19POS
EEM28DTBI CONN EDGECARD 56POS R/A .156 SLD
ADR02ARZ-REEL IC VREF SERIES PREC 5V 8-SOIC
EA-OEM-410 KIT LPC3250 259 WITH QVGA
VI-J7P-EZ CONVERTER MOD DC/DC 13.8V 25W
相關代理商/技術參數
參數描述
DEMO-MSA 制造商:Avago Technologies 功能描述:DEMOBOARD MSA-XX05,10,11,36,70,86 - Bulk
DEMONB5CP1V1 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO
DEMO-NB5CP1V1 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB5 CP1 PLC Sales Demo
DEMO-NB7CP1V1 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB7 CP1 PLC Sales Demo
DEMO-NJ51-KIT-ECT-0-V1 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NJ5 Demo UGKIT, TJG5ML2 to NJE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*