- 您現在的位置：買賣IC網 > PDF目錄17066 > DC745A (Linear Technology)BOARD DELTA SIGMA ADC LTC2433-1 PDF資料下載
參數資料
| 型號： | DC745A |
| 廠商： | Linear Technology |
| 文件頁數： | 2/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2433-1 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC745A Design File DC745A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval™ |
| ADC 的數量： | 2 |
| 位數： | 16 |
| 采樣率（每秒）： | 6.8 |
| 數據接口： | MICROWIRE?，串行，SPI? |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2433-1 |
| 已供物品： | 板 |
| 相關產品： | LTC2433-1IMS#PBF-ND - IC ADC DIFF 16BIT 3WIRE 10-MSOP LTC2433-1CMS#TRPBF-ND - IC ADC DIFF 16BIT 3WIRE 10-MSOP LTC2433-1IMS#TRPBF-ND - IC ADC DIFF 16BIT 3WIRE 10-MSOP LTC2433-1CMS#PBF-ND - IC ADC DIFF 16BIT 3WIRE 10-MSOP LTC2433-1IMS#TR-ND - IC CONV A/D 16BIT DIFF 10-MSOP LTC2433-1CMS#TR-ND - IC CONV A/D 16BIT DIFF 10-MSOP LTC2433-1IMS-ND - IC CONV A/D 16BIT DIFF 10-MSOP LTC2433-1CMS-ND - IC ADC DIFF 16BIT 3WIRE 10-MSOP |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2433-1
10
24331fa
Bit 18 (first output bit) is the end of conversion (EOC)
indicator. This bit is available at the SDO pin during the
conversion and sleep states whenever the CS pin is LOW.
This bit is HIGH during the conversion and goes LOW
when the conversion is complete.
Bit 17 (second output bit) is a dummy bit (DMY) and is
always LOW.
Bit 16 (third output bit) is the conversion result sign indi-
cator (SIG). If VIN is >0, this bit is HIGH. If VIN is <0, this
bit is LOW.
Bit 15 (fourth output bit) is the most significant bit (MSB)
of the result. This bit in conjunction with Bit 16 also
provides the underrange or overrange indication. If both
Bit 16 and Bit 15 are HIGH, the differential input voltage is
above +FS. If both Bit 16 and Bit 15 are LOW, the
differential input voltage is below –FS.
The function of these bits is summarized in Table 1.
Table 1. LTC2433-1 Status Bits
Bit 18 Bit 17 Bit 16 Bit 15
Input Range
EOC
DMY
SIG
MSB
VIN ≥ 0.5 VREF
0011
0V
≤ VIN < 0.5 VREF
0010
–0.5 VREF ≤ VIN < 0V
0001
VIN < – 0.5 VREF
0000
Bits 15-0 are the 16-Bit conversion result MSB first.
Bit 0 is the least significant bit (LSB).
Data is shifted out of the SDO pin under control of the serial
clock (SCK), see Figure 3. Whenever CS is HIGH, SDO
remains high impedance and any externally generated
SCK clock pulses are ignored by the internal data out shift
register.
In order to shift the conversion result out of the device, CS
must first be driven LOW. EOC is seen at the SDO pin of the
device once CS is pulled LOW. EOC changes real time from
HIGH to LOW at the completion of a conversion. This
signal may be used as an interrupt for an external micro-
controller. Bit 18 (EOC) can be captured on the first rising
edge of SCK. Bit 17 is shifted out of the device on the first
falling edge of SCK. The final data bit (Bit 0) is shifted out
on the falling edge of the 18th SCK and may be latched on
the rising edge of the 19th SCK pulse. On the falling edge
of the 19th SCK pulse, SDO goes HIGH indicating the
initiation of a new conversion cycle. This bit serves as EOC
(Bit 18) for the next conversion cycle. Table 2 summarizes
the output data format.
In order to remain compatible with some SPI
microcontrollers, more than 19 SCK clock pulses may be
applied. As long as these clock edges are complete before
the conversion ends, they will not effect the serial data.
However, switching SCK during a conversion may gener-
ate ground currents in the device leading to extra offset
and noise error sources.
As long as the voltage on the analog input pins is main-
tained within the – 0.3V to (VCC + 0.3V) absolute maximum
operating range, a conversion result is generated for any
differential input voltage VIN from –FS = –0.5 VREF to
+FS = 0.5 VREF. For differential input voltages greater than
+FS, the conversion result is clamped to the value corre-
sponding to the +FS + 1LSB. For differential input voltages
below –FS, the conversion result is clamped to the value
corresponding to –FS – 1LSB.
Figure 3. Output Data Timing
MSB
SIG
“O”
1
2
3
4
5
171819
BIT 0
BIT 14
BIT 1
LSB16
BIT 15
BIT 16
BIT 17
SDO
SCK
CS
EOC
BIT 18
SLEEP
DATA OUTPUT
CONVERSION
24331 F03
Hi-Z
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| RMM08DRXS | CONN EDGECARD 16POS DIP .156 SLD |
| SC75B-100 | INDUCTOR SMD 10UH 2.30A 2.52MHZ |
| RBM11DRAH | CONN EDGECARD 22POS R/A .156 SLD |
| CI160808-12NJ | INDUCTOR 12NH 300MA SMD |
| 0210490986 | CABLE JUMPER 1.25MM .030M 29POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC746A | 功能描述:BOARD DELTA SIGMA ADC LTC2412 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC74HC259 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:High Speed CMOS Logic 8-Bit Addressable Latch |
| DC-750 | 制造商:Bivar 功能描述:CARD GUIDE DEEP 7.5" 0.08" BK |
| DC-750-102 | 制造商:Bivar 功能描述:CARD GUIDE DEEP 7.5" 0.102" BK |
| DC-750-102-CI | 制造商:Bivar 功能描述:CARD GUIDE INSERT 7.5" 0.102" BK |
發布緊急采購，3分鐘左右您將得到回復。