參數資料
型號： ADV7162KS140
廠商： ANALOG DEVICES INC
元件分類： 顯示控制器
英文描述： 96-Bit, 220 MHz True-Color Video RAM-DAC
中文描述： 1600 X 1200 PIXELS PALETTE-DAC DSPL CTLR, PQFP160
封裝： PLASTIC, QFP-160
文件頁數： 14/44頁
文件大小： 668K
代理商： ADV7162KS140
REV. 0
–14–
ADV7160/ADV7162
Mnemonic
Function
SYNCOUT
Composite-Sync Output (TTL Compatible Output). This video output is a delayed version of
SYNC
. The delay corresponds to the number of pipeline stages of the device.
Composite-Sync HDTV Control (TTL Compatible Output). This video input is enabled using Bit
CR17 in Command Register 1. When
TRISYNC
is low, any DAC output which has Sync enabled,
goes to the tri-sync level. As with the
SYNC
input, it should only be activated while
BLANK
is low.
Data Bus (TTL Compatible Input/Output Bus). Data, including color palette values and device con-
trol information is written to and read from the device over this 10-bit, bidirectional databus. 10-bit
data or 8-bit data can be used. The databus can be configured for either 10-bit parallel data or byte
data (8+2) as well as standard 8-bit data. Any unused bits of the data bus should be terminated
through a resistor to either the digital power plane (V
CC
) or GND.
Odd/Even Control (TTL Compatible Input). This input indicates which field of the frame is being
displayed. It is required to ensure proper operation of the ADV7160/ADV7162 cursor when inter-
laced display mode is selected. It is ignored when noninterlaced display mode is selected. This input
should change only during the vertical blank period. It is assumed that an odd field will always follow
an even field and vice versa.
Chip Enable (TTL Compatible Input). This input must be at Logic “0” when writing to or reading
from the device over the data bus (D0–D9). Internally, data is latched on the rising edge of
CE
.
Read/Write Control (TTL Compatible Input). This input determines whether data is written to or
read from the device’s registers and color palette RAM. R
/W
and
CE
must be at Logic “0” to write
data to the part. R
/W
must be at Logic “1” and
CE
at Logic “0” to read from the device.
Command Controls (TTL Compatible Inputs). These inputs determine the type of read or write op-
eration being performed on the device over the data bus, (see Interface Truth Table). Data on these
inputs is latched on the falling edge of
CE.
Red, Green & Blue Current Outputs (High Impedance Current Sources). These RGB video outputs
are specified to directly drive RS-343A and RS-170 video levels into doubly terminated 75
loads.
Voltage Reference Input (Analog Input): An external 1.235 V voltage reference is required to drive
this input. An AD589 (2-terminal voltage reference) or equivalent is recommended. (Note: It is not
recommended to use a resistor network to generate the voltage reference.)
Output Full Scale Adjust Control (Analog Input). A resistor connected between this pin and analog
ground controls the absolute amplitude of the output video signal. For a value of R
SET
of nominally
280
, with 37.5
termination and using CR43 and CR44 of Command Register 4 to set the DAC
Gain as shown, the required Video Standard can be achieved.
CR44
CR43
Video Standard
0
0
RS343A, Sync & Pedestal
0
1
RS343A, Sync & No Pedestal
1
0
RS343A, No Sync & No Pedestal
1
1
RS170, Sync & Pedestal
Alternatively, R
SET
can be calculated by the following equation:
DAC Gain
×
V
REF
Black toWhite Current
TRISYNC
D9–D0
ODD/
EVEN
CE
R
/W
C0, C1
IOR, IOG, IOB
V
REF
R
SE
T
DAC Gain
3996
4224
4311
5592
Black to White
660 mV 17.62 mA
699 mV 18.63 mA
714 mV 19.05 mA
925 mV 24.67 mA
R
SET
COMP
V
AA
Compensation Pin. A 0.1
μ
F capacitor should be connected between this pin and V
AA
.
Power Supply (+5 V
±
5%). The part contains multiple power supply pins, all should be connected
together to one common +5 V filtered analog power supply.
Analog Ground. The part contains multiple ground pins, all should be connected together to the
system’s ground plane.
These four pins control the JTAG test access port.
See Appendix 6 for more detail
GND:
TMS, TCK,
TDI, TDO
相關PDF資料
PDF描述
ADV7162KS170 96-Bit, 220 MHz True-Color Video RAM-DAC
ADV7162KS220 96-Bit, 220 MHz True-Color Video RAM-DAC
ADV7160KS140 96-Bit, 220 MHz True-Color Video RAM-DAC
ADV7160KS170 96-Bit, 220 MHz True-Color Video RAM-DAC
ADV7160KS220 96-Bit, 220 MHz True-Color Video RAM-DAC
相關代理商/技術參數
參數描述
ADV7162KS170 制造商:AD 制造商全稱:Analog Devices 功能描述:96-Bit, 220 MHz True-Color Video RAM-DAC
ADV7162KS220 制造商:Analog Devices 功能描述:DAC 3-CH Segment 10-bit 160-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:220 MHZ VIDEO RAM DAC I.C. - Bulk
ADV7162KSZ140 制造商:Analog Devices 功能描述:DAC 3-CH Segment 10-bit 160-Pin MQFP
ADV7162KSZ220 制造商:Analog Devices 功能描述:DAC 3-CH Segment 10-bit 160-Pin MQFP
ADV7170 制造商:AD 制造商全稱:Analog Devices 功能描述:Digital PAL/NTSC Video Encoder with 10-Bit SSAF⑩ and Advanced Power Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*