- 您現在的位置：買賣IC網 > PDF目錄374045 > ADV7162 (Analog Devices, Inc.) 96-Bit, 220 MHz True-Color Video RAM-DAC(96位,220MHz,真彩色視頻RAM-D/A轉換器) PDF資料下載
參數資料
| 型號： | ADV7162 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 96-Bit, 220 MHz True-Color Video RAM-DAC(96位,220MHz,真彩色視頻RAM-D/A轉換器) |
| 中文描述： | 96位，220 MHz的真彩色視頻RAM - DAC的（96位，220MHz，真彩色視頻RAM的的D / A轉換器） |
| 文件頁數： | 34/44頁 |
| 文件大?。?/td> | 687K |
| 代理商： | ADV7162 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
REV. 0
–34–
ADV7160/ADV7162
APPENDIX 1
BOARD DESIGN AND LAYOUT CONSIDERATIONS
The ADV7160/ADV7162 is a highly integrated circuit contain-
ing both precision analog and high speed digital circuitry. It has
been designed to minimize interference effects on the integrity
of the analog circuitry by the high speed digital circuitry. It is
imperative that these same design and layout techniques be ap-
plied to the system level design such that high speed, accurate
performance is achieved. The “Recommended Analog Circuit
Layout” shows the analog interface between the device and
monitor.
The layout should be optimized for lowest noise on the
ADV7160/ADV7162 power and ground lines by shielding the
digital inputs and providing good decoupling. The lead length
between groups of V
AA
and GND pins should by minimized so
as to minimize inductive ringing.
Ground Planes
The ground plane should encompass all ADV7160/ADV7162
ground pins, voltage reference circuitry, power supply bypass
circuitry for the ADV7160/ADV7162, the analog output traces,
and all the digital signal traces leading up to the ADV7160/
ADV7162. The ground plane is the graphics board's common
ground plane.
Power Planes
The ADV7160/ADV7162 and any associated analog circuitry
should have it’s own power plane, referred to as the analog
power plane (V
AA
). This power plane should be connected to
the regular PCB power plane (V
CC
) at a single point through a
ferrite bead. This bead should be located within three inches of
the ADV7160/ADV7162.
The PCB power plane should provide power to all digital logic
on the PC board, and the analog power plane should provide
power to all ADV7160/ADV7162 power pins and voltage refer-
ence circuitry.
Plane-to-plane noise coupling can be reduced by ensuring that
portions of the regular PCB power and ground planes do not
overlay portions of the analog power plane, unless they can be
arranged such that the plane-to-plane noise is common mode.
Supply Decoupling
For optimum performance, bypass capacitors should be in-
stalled using the shortest leads possible, consistent with reliable
operation, to reduce the lead inductance. Best performance is
obtained with 0.1
μ
F ceramic capacitor decoupling. Each group
of V
AA
pins on the ADV7160/ADV7162 must have at least one
0.1
μ
F decoupling capacitor to GND. These capacitors should
be placed as close as possible to the device.
It is important to note that while the ADV7160/ADV7162 con-
tains circuitry to reject power supply noise, this rejection de-
creases with frequency. If a high frequency switching power
supply is used, the designer should pay close attention to reduc-
ing power supply noise and consider using a three terminal volt-
age regulator for supplying power to the analog power plane.
Digital Signal Interconnect
The digital inputs to the ADV7160/ADV7162 should be iso-
lated as much as possible from the analog outputs and other
analog circuitry. Also, these input signals should not overlay the
analog power plane.
Due to the high clock rates involved, long clock lines to the
ADV7160/ADV7162 should be avoided to reduce noise pickup.
Any active termination resistors for the digital inputs should be
connected to the regular PCB power plane (V
CC
), and not the
analog power plane.
Analog Signal Interconnect
The ADV7160/ADV7162 should be located as close as possible
to the output connectors to minimize noise pickup and reflec-
tions due to impedance mismatch.
The video output signals should overlay the ground plane, and
not the analog power plane, to maximize the high frequency
power supply rejection.
Digital Inputs, especially Pixel Data Inputs and clocking signals
(CLOCK, LOADOUT, LOADIN, etc.) should never overlay
any of the analog signal circuitry and should be kept as far away
as possible.
For best performance, the analog outputs (IOR, IOG, IOB)
should each have a 75
load resistor connected to GND.
These resistors should be placed as close as possible to the
ADV7160/ADV7162 so as to minimize reflections.
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7162KS140 | 96-Bit, 220 MHz True-Color Video RAM-DAC |
| ADV7162KS170 | 96-Bit, 220 MHz True-Color Video RAM-DAC |
| ADV7162KS220 | 96-Bit, 220 MHz True-Color Video RAM-DAC |
| ADV7160KS140 | 96-Bit, 220 MHz True-Color Video RAM-DAC |
| ADV7160KS170 | 96-Bit, 220 MHz True-Color Video RAM-DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7162KS140 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADV7162KS170 | 制造商:AD 制造商全稱:Analog Devices 功能描述:96-Bit, 220 MHz True-Color Video RAM-DAC |
| ADV7162KS220 | 制造商:Analog Devices 功能描述:DAC 3-CH Segment 10-bit 160-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:220 MHZ VIDEO RAM DAC I.C. - Bulk |
| ADV7162KSZ140 | 制造商:Analog Devices 功能描述:DAC 3-CH Segment 10-bit 160-Pin MQFP |
| ADV7162KSZ220 | 制造商:Analog Devices 功能描述:DAC 3-CH Segment 10-bit 160-Pin MQFP |
發布緊急采購，3分鐘左右您將得到回復。