參數資料
型號： ADUC7023BCPZ62I-R7
廠商： Analog Devices Inc
文件頁數： 62/96頁
文件大?。?/td> 0K
描述： IC MCU 12BIT 62KB FLASH 32LFCSP
標準包裝： 1,500
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 44MHz
連通性： I²C，SPI
外圍設備： POR，PWM，WDT
輸入/輸出數： 12
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 2K x 32
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
數據轉換器： A/D 8x12b，D/A 4x12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 32-WFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
Data Sheet
ADuC7023
| Page 65 of 96
Table 73. I2CxSSTA MMR Bit Designations
Bit
Name
Description
15
Reserved bit.
14
I2CSTA
This bit is set to 1 if: A start condition followed by a matching address is detected. It is also set if a start
byte (0x01) is received. If general calls are enabled and a general call code of (0x00) is received.
This bit is cleared on receiving a stop condition.
13
I2CREPS
This bit is set to 1 if a repeated start condition is detected.
This bit is cleared on receiving a stop condition.
12 to 11
I2CID[1:0]
I2C address matching register. These bits indicate which I2CxIDx register matches the received address.
[00] = received address matches I2CxID0.
[01] = received address matches I2CxID1.
[10] = received address matches I2CxID2.
[11] = received address matches I2CxID3.
10
I2CSS
I2C stop condition after start detected bit.
This bit is set to 1 when a stop condition is detected after a previous start and matching address.
When the I2CSSENI bit in I2CxSCON is set, an interrupt is generated.
This bit is cleared by reading this register.
9 to 8
I2CGCID[1:0]
I2C general call ID bits.
[00] = no general call received.
[01] = general call reset and program address.
[10] = general program address.
[11] = general call matching alternative ID.
These bits are not cleared by a general call reset command.
These bits are cleared by writing a 1 to the I2CGCCLR bit in I2CxSCON.
7
I2CGC
I2C general call status bit.
This bit is set to 1 if the slave receives a general call command of any type. If the command received is a
reset command, then all registers return to their default state. If the command received is a hardware
general call, the Rx FIFO holds the second byte of the command, and this can be compared with the
I2CxALT register.
This bit is cleared by writing a 1 to the I2CGCCLR bit in I2CxSCON.
6
I2CSBUSY
I2C slave busy status bit.
This bit is set to 1 when the slave receives a start condition.
This bit is cleared by hardware if the received address does not match any of the I2CxIDx registers, the
slave device receives a stop condition or if a repeated start address does not match any of the I2CxIDx
registers.
5
I2CSNA
I2C slave no acknowledge data bit.
This bit is set to 1 when the slave responds to a bus address with a no acknowledge. This bit is asserted
under the following conditions: if no acknowledge is returned because there is no data in the Tx FIFO or if
the I2CNACKEN bit is set in the I2CxSCON register.
This bit is cleared in all other conditions.
4
I2CSRxFO
Slave Rx FIFO overflow.
This bit is set to 1 when a byte is written to the Rx FIFO when it is already full.
This bit is cleared in all other conditions.
3
I2CSRXQ
I2C slave receive request bit.
This bit is set to 1 when the slave Rx FIFO is not empty. This bit causes an interrupt to occur if the
I2CSRXENI bit in I2CxSCON is set.
The Rx FIFO must be read or flushed to clear this bit.
2
I2CSTXQ
I2C slave transmit request bit.
This bit is set to 1 when the slave receives a matching address followed by a read. If the I2CSETEN bit in
I2CxSCON is = 0, , this bit goes high just after the negative edge of SCL during the read bit transmission. If
the I2CSETEN bit in I2CxSCON is = 1, this bit goes high just after the positive edge of SCL during the read
bit transmission. This bit causes an interrupt to occur if the I2CSTXENI bit in I2CxSCON is set.
This bit is cleared in all other conditions.
Rev. E
相關PDF資料
PDF描述
ADUC7024BCPZ62 IC MCU FLSH 62K ANLG I/O 64LFCSP
ADUC7032BSTZ-88 IC MCU 96K FLASH DUAL 48LQFP
ADUC7032BSTZ-8V-RL IC BATTERY SENSOR PREC 48-LQFP
ADUC7034BCPZ IC MCU FLASH 32K ANLG IO 48LFCSP
ADUC7036CCPZ IC MCU 96K FLASH DUAL 48LFCSP
相關代理商/技術參數
參數描述
ADUC7023BCPZ62I-RL 功能描述:IC MCU 12BIT 62KB FLASH 32LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7024 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU
ADUC7024BCP62 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC &2X12-B DAC IC - Trays
ADUC7024BCP62-U1 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC &2X12-B DAC IC - Trays
ADUC7024BCPZ62 功能描述:IC MCU FLSH 62K ANLG I/O 64LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:60 系列:PSOC® 3 CY8C38xx 核心處理器:8051 芯體尺寸:8-位 速度:67MHz 連通性:EBI/EMI，I²C，LIN，SPI，UART/USART 外圍設備:電容感應，DMA，LCD，POR，PWM，WDT 輸入/輸出數:25 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:2K x 8 RAM 容量:8K x 8 電壓 - 電源 (Vcc/Vdd):1.71 V ~ 5.5 V 數據轉換器:A/D 2x20b，D/A 4x8b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:48-VFQFN 裸露焊盤 包裝:托盤
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*