- 您現在的位置：買賣IC網 > PDF目錄1900 > ADSP-TS203SABP-050 (Analog Devices Inc)IC DSP FLOAT/FIXED 500MHZ 576BGA PDF資料下載
參數資料
| 型號： | ADSP-TS203SABP-050 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/48頁 |
| 文件大小： | 0K |
| 描述： | IC DSP FLOAT/FIXED 500MHZ 576BGA |
| 標準包裝： | 1 |
| 系列： | TigerSHARC® |
| 類型： | 定點/浮點 |
| 接口： | 主機接口，連接端口，多處理器 |
| 時鐘速率： | 500MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 512kB |
| 電壓 - 輸入/輸出： | 2.50V |
| 電壓 - 核心： | 1.05V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 576-BBGA 裸露焊盤 |
| 供應商設備封裝： | 576-BGA-ED（25x25） |
| 包裝： | 托盤 |
| 其它名稱： | ADSP-TS203SABP050 ADSP-TS203SABP050-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Rev. D
|
Page 18 of 48
|
May 2012
STRAP PIN FUNCTION DESCRIPTIONS
Some pins have alternate functions at reset. Strap options set
processor operating modes. During reset, the processor samples
the strap option pins. Strap pins have an internal pull-up or
pull-down for the default value. If a strap pin is not connected to
an overdriving external pull-up, pull-down, or logic load, the
processor samples the default value during reset. If strap pins
are connected to logic inputs, a stronger external pull-up or
pull-down may be required to ensure default value depending
on leakage and/or low level input current of the logic load. To
set a mode other than the default mode, connect the strap pin to
a sufficiently stronger external pull-up or pull-down. Table 16
lists and describes each of the processor’s strap pins.
Table 15. Pin Definitions—Power, Ground, and Reference
Signal
Type
Term
Description
VDD
Pna
VDD pins for internal logic.
VDD_A
Pna
VDD pins for analog circuits. Pay critical attention to bypassing this supply.
VDD_IO
Pna
VDD pins for I/O buffers.
VDD_DRAM
Pna
VDD pins for internal DRAM.
VREF
I
na
Reference voltage defines the trip point for all input buffers, except SCLK, RST_IN,
POR_IN, IRQ3–0, FLAG3–0, DMAR3–0, ID2–0, CONTROLIMP1–0, LxDATO3–0P/N,
LxCLKOUTP/N, LxDATI3–0P/N, LxCLKINP/N, TCK, TDI, TMS, and TRST. VREF can be
connected to a power supply or set by a voltage divider circuit as shown in Figure 4.
SCLK_VREF
I
na
System Clock Reference. Connect this pin to a reference voltage as shown in
VSS
Gna
Ground pins.
NC
—
nc
No Connect. Do not connect these pins to anything (not to any supply, signal, or
each other). These pins are reserved and must be left unconnected.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 kΩ to VSS; epu = external pull-up
approximately 5 kΩ to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect
directly to VSS
Table 16. Pin Definitions—I/O Strap Pins
Signal
Type (at
Reset)
On Pin …
Description
EBOOT
I (pd_0)
BMS
EPROM Boot.
0 = boot from EPROM immediately after reset (default)
1 = idle after reset and wait for an external device to boot processor through the
external port or a link port
IRQEN
I (pd)
BM
Interrupt Enable.
0 = disable and set IRQ3–0 interrupts to edge-sensitive after reset (default)
1 = enable and set IRQ3–0 interrupts to level-sensitive immediately after reset
LINK_DWIDTH
I (pd)
TMR0E
Link Port Input Default Data Width.
0 = 1-bit (default)
1 = 4-bit
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5kΩ; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on processor ID = 0; pu_0 = internal pull-up 5 kΩ on processor ID = 0;
pu_od_0 = internal pull-up 500 Ω on processor ID = 0; pd_m = internal pull-down 5 kΩ on processor bus master; pu_m = internal pull-up
5 kΩ on processor bus master; pu_ad = internal pull-up 40 kΩ. For more pull-down and pull-up information, see Electrical Characteristics
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7021BCPZ62-RL7 | IC MCU 12BIT 1MSPS UART 40-LFCSP |
| ADUC7023BCPZ62I-R7 | IC MCU 12BIT 62KB FLASH 32LFCSP |
| ADUC7024BCPZ62 | IC MCU FLSH 62K ANLG I/O 64LFCSP |
| ADUC7032BSTZ-88 | IC MCU 96K FLASH DUAL 48LQFP |
| ADUC7032BSTZ-8V-RL | IC BATTERY SENSOR PREC 48-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-TS203SABP-05X | 制造商:Analog Devices 功能描述: |
| ADSP-TS203SABPZ050 | 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS203SBBPZ050 | 制造商:Analog Devices 功能描述:DSP - Bulk |
| ADSQ-1410 | 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
| ADSQ-1410-C | 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。