- 您現在的位置：買賣IC網 > PDF目錄1900 > ADSP-TS202SABPZ050 (Analog Devices Inc)IC PROCESSOR 500MHZ 576BGA PDF資料下載
參數資料
| 型號： | ADSP-TS202SABPZ050 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 34/48頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROCESSOR 500MHZ 576BGA |
| 標準包裝： | 1 |
| 系列： | TigerSHARC® |
| 類型： | 定點/浮點 |
| 接口： | 主機接口，連接端口，多處理器 |
| 時鐘速率： | 500MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 1.5MB |
| 電壓 - 輸入/輸出： | 2.50V |
| 電壓 - 核心： | 1.05V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 576-BBGA 裸露焊盤 |
| 供應商設備封裝： | 576-BGA-ED（25x25） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Rev. C
|
Page 4 of 48
|
December 2006
ADSP-TS202S
The TigerSHARC DSP uses a Static Superscalar
TM architecture.
This architecture is superscalar in that the ADSP-TS202S pro-
cessor’s core can execute simultaneously from one to four 32-bit
instructions encoded in a very large instruction word (VLIW)
instruction line using the DSP’s dual compute blocks. Because
the DSP does not perform instruction reordering at runtime—
the programmer selects which operations will execute in parallel
prior to runtime—the order of instructions is static.
With few exceptions, an instruction line, whether it contains
one, two, three, or four 32-bit instructions, executes with a
throughput of one cycle in a 10-deep processor pipeline.
For optimal DSP program execution, programmers must follow
the DSP’s set of instruction parallelism rules when encoding an
instruction line. In general, the selection of parallel instructions
that the DSP can execute in each cycle depends on both the
instruction line resources each instruction requires and on the
source and destination registers used in the instructions. The
programmer has direct control of three core components—the
IALUs, the compute blocks, and the program sequencer.
The ADSP-TS202S processor, in most cases, has a two-cycle
execution pipeline that is fully interlocked, so—whenever a
computation result is unavailable for another operation depen-
dent on it—the DSP automatically inserts one or more stall
cycles as needed. Efficient programming with dependency-free
instructions can eliminate most computational and memory
transfer data dependencies.
In addition, the ADSP-TS202S processor supports SIMD opera-
tions two ways—SIMD compute blocks and SIMD
computations. The programmer can load both compute blocks
with the same data (broadcast distribution) or different data
(merged distribution).
DUAL COMPUTE BLOCKS
The ADSP-TS202S processor has compute blocks that can
execute computations either independently or together as a sin-
gle-instruction, multiple-data (SIMD) engine. The DSP can
issue up to two compute instructions per compute block each
cycle, instructing the ALU, multiplier, or shifter to perform
independent, simultaneous operations. Each compute block can
execute eight 8-bit, four 16-bit, two 32-bit, or one 64-bit SIMD
computations in parallel with the operation in the other block.
These computation units support IEEE 32-bit single-precision
floating-point, extended-precision 40-bit floating point, and
8-, 16-, 32-, and 64-bit fixed-point processing.
The compute blocks are referred to as X and Y in assembly
syntax, and each block contains three computational units—an
ALU, a multiplier, and a 64-bit shifter—and a 32-word
register file.
Register File—each compute block has a multiported,
32-word, fully orthogonal register file used for transferring
data between the computation units and data buses and for
storing intermediate results. Instructions can access the
registers in the register file individually (word-aligned), in
sets of two (dual-aligned), or in sets of four (quad-aligned).
ALU—the ALU performs a standard set of arithmetic oper-
ations in both fixed- and floating-point formats. It also
performs logic and permute operations.
Multiplier—the multiplier performs both fixed- and float-
ing-point multiplication and fixed-point multiply and
accumulate.
Shifter—the 64-bit shifter performs logical and arithmetic
shifts, bit and bit stream manipulation, and field deposit
and extraction operations.
Using these features, the compute blocks can
Provide 8 MACS per cycle peak and 7.1 MACS per cycle
sustained 16-bit performance and provide 2 MACS per
cycle peak and 1.8 MACS per cycle sustained 32-bit perfor-
mance (based on FIR)
Execute six single-precision floating-point or execute 24
fixed-point (16-bit) operations per cycle, providing
3G FLOPS or 12.0G/s regular operations performance at
500 MHz
Perform two complex 16-bit MACS per cycle
DATA ALIGNMENT BUFFER (DAB)
The DAB is a quad-word FIFO that enables loading of quad-
word data from nonaligned addresses. Normally, load instruc-
tions must be aligned to their data size so that quad words are
loaded from a quad-aligned address. Using the DAB signifi-
cantly improves the efficiency of some applications, such as
FIR filters.
DUAL INTEGER ALU (IALU)
The ADSP-TS202S processor has two IALUs that provide pow-
erful address generation capabilities and perform many general-
purpose integer operations. The IALUs are referred to as J and
K in assembly syntax and have the following features:
Provide memory addresses for data and update pointers
Support circular buffering and bit-reverse addressing
Perform general-purpose integer operations, increasing
programming flexibility
Include a 31-word register file for each IALU
As address generators, the IALUs perform immediate or indi-
rect (pre- and post-modify) addressing. They perform modulus
and bit-reverse operations with no constraints placed on mem-
ory addresses for the modulus data buffer placement. Each
IALU can specify either a single-, dual-, or quad-word access
from memory.
The IALUs have hardware support for circular buffers, bit
reverse, and zero-overhead looping. Circular buffers facilitate
efficient programming of delay lines and other data structures
required in digital signal processing, and they are commonly
used in digital filters and Fourier transforms. Each IALU pro-
vides registers for four circular buffers, so applications can set
Static Superscalar is a trademark of Analog Devices, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-TS203SABP-050 | IC DSP FLOAT/FIXED 500MHZ 576BGA |
| ADUC7021BCPZ62-RL7 | IC MCU 12BIT 1MSPS UART 40-LFCSP |
| ADUC7023BCPZ62I-R7 | IC MCU 12BIT 62KB FLASH 32LFCSP |
| ADUC7024BCPZ62 | IC MCU FLSH 62K ANLG I/O 64LFCSP |
| ADUC7032BSTZ-88 | IC MCU 96K FLASH DUAL 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-TS203SABP-050 | 功能描述:IC DSP FLOAT/FIXED 500MHZ 576BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS203SABP-05X | 制造商:Analog Devices 功能描述: |
| ADSP-TS203SABPZ050 | 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:TigerSHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-TS203SBBPZ050 | 制造商:Analog Devices 功能描述:DSP - Bulk |
| ADSQ-1410 | 制造商:MURATA-PS 制造商全稱:Murata Power Solutions Inc. 功能描述:Quad 14-Bit, 10 MSPS Sampling A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。