- 您現在的位置：買賣IC網 > PDF目錄19377 > ADSP-BF535PBB-300 (Analog Devices Inc)IC DSP CONTROLLER 16BIT 260BGA PDF資料下載
參數資料
| 型號： | ADSP-BF535PBB-300 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 260BGA |
| 產品培訓模塊： | Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services |
| 標準包裝： | 1 |
| 系列： | Blackfin® |
| 類型： | 定點 |
| 接口： | PCI，SPI，SSP，UART，USB |
| 時鐘速率： | 300MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 308kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 1.50V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 260-BBGA |
| 供應商設備封裝： | 260-PBGA（19x19） |
| 包裝： | 托盤 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
ADSP-BF535
–10–
REV. A
Framing—Each transmit and receive port can run with or
without frame sync signals for each data-word. Frame
sync signals can be generated internally or externally,
active high or low, with either of two pulse widths and
early or late frame sync.
Companding in hardware—Each SPORT can perform
A-law or -law companding according to ITU recommen-
dation G.711. Companding can be selected on the
transmit and/or receive channel of the SPORT without
additional latencies.
DMA operations with single-cycle overhead—Each
SPORT can automatically receive and transmit multiple
buffers of memory data. The Blackfin processor can link
or chain sequences of DMA transfers between a SPORT
and memory. The chained DMA can be dynamically
allocated and updated through the descriptor blocks that
set up the chain.
Interrupts—Each transmit and receive port generates an
interrupt upon completing the transfer of a data-word or
after transferring an entire data buffer or buffers through
the DMA.
Multichannel capability—Each SPORT supports 128
channels and is compatible with the H.100, H.110,
MVIP-90, and HMVIP standards.
Serial Peripheral Interface (SPI) Ports
The ADSP-BF535 Blackfin processor has two SPI compatible
ports that enable the processor to communicate with multiple
SPI compatible devices.
The SPI interface uses three pins for transferring data: two data
pins (Master Output-Slave Input, MOSIx, and Master Input-
Slave Output, MISOx) and a clock pin (Serial Clock, SCKx).
Two SPI chip select input pins (
SPISSx) let other SPI devices
select the processor, and fourteen SPI chip select output pins
(SPIxSEL7–1) let the processor select other SPI devices. The SPI
select pins are reconfigured programmable flag pins. Using these
pins, the SPI ports provide a full duplex, synchronous serial inter-
face, which supports both master and slave modes and
multimaster environments.
Each SPI port’s baud rate and clock phase/polarities are program-
mable (see Figure 4), and each has an integrated DMA
controller, configurable to support transmit or receive data
streams. The SPI’s DMA controller can only service unidirec-
tional accesses at any given time.
During transfers, the SPI ports simultaneously transmit and
receive by serially shifting data in and out on two serial data lines.
The serial clock line synchronizes the shifting and sampling of
data on the two serial data lines.
In master mode, the processor performs the following sequence
to set up and initiate SPI transfers:
1. Enables and configures the SPI port’s operation (data
size and transfer format).
2. Selects the target SPI slave with an SPIxSELy output pin
(reconfigured programmable flag pin).
3. Defines one or more TCBs in the processor’s memory
space (optional in DMA mode only).
4. Enables the SPI DMA engine and specifies transfer
direction (optional in DMA mode only).
5. Reads or writes the SPI port receive or transmit data
buffer (in non-DMA mode only).
The SCKx line generates the programmed clock pulses
for simultaneously shifting data out on MOSIx and
shifting data in on MISOx. In the DMA mode only,
transfers continue until the SPI DMA word count transi-
tions from 1 to 0.
In slave mode, the processor performs the following sequence to
set up the SPI port to receive data from a master transmitter:
1. Enables and configures the SPI slave port to match the
operation parameters set up on the master (data size and
transfer format) SPI transmitter.
2. Defines and generates a receive TCB in the processor’s
memory space to interrupt at the end of the data transfer
(optional in DMA mode only).
3. Enables the SPI DMA engine for a receive access
(optional in DMA mode only).
4. Starts receiving data on the appropriate SPI SCKx edges
after receiving an SPI chip select on an
SPISSx input pin
(reconfigured programmable flag pin) from a master.
In DMA mode only, reception continues until the SPI DMA
word count transitions from 1 to 0. The processor can continue,
by queuing up the next command TCB.
A slave mode transmit operation is similar, except the processor
specifies the data buffer in memory from which to transmit data,
generates and relinquishes control of the transmit TCB, and
begins filling the SPI port’s data buffer. If the SPI controller is
not ready to transmit, it can transmit a “zero” word.
UART Port
The ADSP-BF535 Blackfin processor provides two full-duplex
Universal Asynchronous Receiver/Transmitter (UART) ports
(UART0 and UART1) fully compatible with PC-standard
UARTs. The UART ports provide a simplified UART interface
to other peripherals or hosts, supporting full-duplex, DMA-sup-
ported, asynchronous transfers of serial data. Each UART port
Figure 4. SPI Clock Rate Calculation
SPI Clock Rate
fSCLK
2
SPIBAUD
×
-------------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| GBM08DRMH | CONN EDGECARD 16POS .156 WW |
| VI-B1R-CV-F4 | CONVERTER MOD DC/DC 7.5V 150W |
| GBM08DRMD | CONN EDGECARD 16POS .156 WW |
| VJ1206A680JBCAT4X | CAP CER 68PF 200V 5% NP0 1206 |
| VI-B1R-CV-F3 | CONVERTER MOD DC/DC 7.5V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-BF535PBBZ-200 | 功能描述:IC DSP CONTROLLER 16BIT 260-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSPBF535PKB300 | 制造商:Analog Devices 功能描述: |
| ADSP-BF535PKB-300 | 功能描述:IC DSP CONTROLLER 16BIT 260 BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-BF535PKB-350 | 功能描述:IC DSP CONTROLLER 16BIT 260 BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:Blackfin® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-BF535PKB-C91 | 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。