- 您現在的位置：買賣IC網 > PDF目錄1900 > ADSP-21990BSTZ (Analog Devices Inc)IC DSP CONTROLLER 16BIT 176-LQFP PDF資料下載
參數資料
| 型號： | ADSP-21990BSTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/50頁 |
| 文件大小： | 0K |
| 描述： | IC DSP CONTROLLER 16BIT 176-LQFP |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 標準包裝： | 1 |
| 系列： | ADSP-21xx |
| 類型： | 定點 |
| 接口： | SPI，SSP |
| 時鐘速率： | 160MHz |
| 非易失內存： | 外部 |
| 芯片上RAM： | 20kB |
| 電壓 - 輸入/輸出： | 3.30V |
| 電壓 - 核心： | 2.50V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 176-LQFP |
| 供應商設備封裝： | 176-LQFP（24x24） |
| 包裝： | 托盤 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Rev. A
|
Page 10 of 50
|
August 2007
ADSP-21990
Alternative frequency and direction mode.
Single north marker mode.
Count error monitor function with dedicated error
interrupt.
Dedicated 16-bit loop timer with dedicated interrupt.
Companion encoder event (1T) timer unit.
The encoder interface unit (EIU) includes a 32-bit quadrature
up-/downcounter, programmable input noise filtering of the
encoder input signals and the zero markers, and has four dedi-
cated chip pins. The quadrature encoder signals are applied at
the EIA and EIB pins. Alternatively, a frequency and direction
set of inputs may be applied to the EIA and EIB pins. In addi-
tion, two north marker/strobe inputs are provided on pins EIZ
and EIS. These inputs may be used to latch the contents of the
encoder quadrature counter into dedicated registers,
EIZLATCH and EISLATCH, on the occurrence of external
events at the EIZ and EIS pins. These events may be pro-
grammed to be either rising edge only (latch event) or rising
edge if the encoder is moving in the forward direction and fall-
ing edge if the encoder is moving in the reverse direction
(software latched north marker functionality).
The encoder interface unit incorporates programmable noise
filtering on the four encoder inputs to prevent spurious noise
pulses from adversely affecting the operation of the quadrature
counter. The encoder interface unit operates at a clock fre-
quency equal to the HCLK rate. The encoder interface unit
operates correctly with encoder signals at frequencies of up to
13.25 MHz at the 80 MHz HCLK rate, corresponding to a maxi-
mum quadrature frequency of 53 MHz (assuming an ideal
quadrature relationship between the input EIA and EIB signals).
The EIU may be programmed to use the north marker on EIZ to
reset the quadrature encoder in hardware, if required.
Alternatively, the north marker can be ignored, and the encoder
quadrature counter is reset according to the contents of a maxi-
mum count register, EIUMAXCNT. There is also a “single
north marker” mode available in which the encoder quadrature
counter is reset only on the first north marker pulse.
The encoder interface unit can also be made to implement some
error checking functions. If an encoder count error is detected
(due to a disconnected encoder line, for example), a status bit in
the EIUSTAT register is set, and an EIU count error interrupt is
generated.
The encoder interface unit of the ADSP-21990 contains a 16-bit
loop timer that consists of a timer register, period register, and
scale register so that it can be programmed to time out and
reload at appropriate intervals. When this loop timer times out,
an EIU loop timer timeout interrupt is generated. This interrupt
could be used to control the timing of speed and position con-
trol loops in high performance drives.
The encoder interface unit also includes a high performance
encoder event timer (EET) block that permits the accurate tim-
ing of successive events of the encoder inputs. The EET can be
programmed to time the duration between up to 255 encoder
pulses and can be used to enhance velocity estimation, particu-
larly at low speeds of rotation.
FLAG I/O (FIO) PERIPHERAL UNIT
The FIO module is a generic parallel I/O interface that supports
16 bidirectional multifunction flags or general-purpose digital
I/O signals (PF15–0).
All 16 FLAG bits can be individually configured as an input or
output based on the content of the direction (DIR) register, and
can also be used as an interrupt source for one of two FIO inter-
rupts. When configured as input, the input signal can be
programmed to set the FLAG on either a level (level sensitive
input/interrupt) or an edge (edge sensitive input/interrupt).
The FIO module can also be used to generate an asynchronous
unregistered wake-up signal FIO_WAKEUP for DSP core wake
up after power-down.
The FIO lines, PF7–1 can also be configured as external slave
select outputs for the SPI communications port, while PF0 can
be configured to act as a slave select input.
The FIO lines can be configured to act as a PWM shutdown
source for the 3-phase PWM generation unit of the
ADSP-21990.
WATCHDOG TIMER
The ADSP-21990 integrates a watchdog timer that can be used
as a protection mechanism against unintentional software
events. It can be used to cause a complete DSP and peripheral
reset in such an event. The watchdog timer consists of a 16-bit
timer that is clocked at the external clock rate (CLKIN or crystal
input frequency).
In order to prevent an unwanted timeout or reset, it is necessary
to periodically write to the watchdog timer register. During
abnormal system operation, the watchdog count will eventually
decrement to 0 and a watchdog timeout will occur. In the sys-
tem, the watchdog timeout will cause a full reset of the DSP core
and peripherals.
GENERAL-PURPOSE TIMERS
The ADSP-21990 contains a general-purpose timer unit that
contains three identical 32-bit timers. The three programmable
interval timers (Timer0, Timer1, and Timer2) generate periodic
interrupts. Each timer can be independently set to operate in
one of three modes:
Pulse waveform generation (PWM_OUT) mode.
Pulse width count/capture (WDTH_CAP) mode.
External event watchdog (EXT_CLK) mode.
Each timer has one bidirectional chip pin, TMR2-0. For each
timer, the associated pin is configured as an output pin in
PWM_OUT mode and as an input pin in WDTH_CAP and
EXT_CLK modes.
INTERRUPTS
The interrupt controller lets the DSP respond to 17 interrupts
with minimum overhead. The DSP core implements an inter-
rupt priority scheme as shown in Table 2. Applications can use
the unassigned slots for software and peripheral interrupts. The
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21991BSTZ | IC DSP CONTROLLER 16BIT 176-LQFP |
| ADSP-21992YBC | IC DSP CTLR 16BIT 196CSPBGA |
| ADSP-3PARCBF548M01 | MODULE BOARD BF548 |
| ADSP-BF506KSWZ-4F | IC DSP 12BIT 400MHZ 120LQFP |
| ADSP-BF518BSWZ-4F4 | IC DSP 16/32B 400MHZ LP 176LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21991BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin Mini-BGA |
| ADSP-21991BBCZ | 功能描述:IC DSP CTLR 16BIT 196CSPBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21991BST | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 160MHz 160MIPS 176-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:HIGH PERFORMANCE MIXED SIGNAL DSP - Bulk |
| ADSP-21991BSTZ | 功能描述:IC DSP CONTROLLER 16BIT 176-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:ADSP-21xx 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，F(xiàn)CBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP-21992BBC | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 150MHz 150MIPS 196-Pin CSP-BGA 制造商:Rochester Electronics LLC 功能描述:MIXED SIGNAL DSP W/32K DM RAM& 16K PMRAM - Bulk |
發布緊急采購，3分鐘左右您將得到回復。