參數資料
型號： ADE7754AR
廠商： ANALOG DEVICES INC
元件分類： 模擬信號調理
英文描述： ADE7754
中文描述： SPECIALTY ANALOG CIRCUIT, PDSO24
封裝： MS-013AD, SOIC-24
文件頁數： 8/44頁
文件大小： 630K
代理商： ADE7754AR
REV. PrG 01/03
PRELIMINARY TECHNICAL DATA
ADE7754
–
8
–
PIN FUNCTION DESCRIPTION
Pin No.
MNEMONIC
DESCRIPTION
1
CF
Calibration Frequency logic output. The CF logic output gives Active Power informa-
tion. This output is intended to be used for operational and calibration purposes. The
full-scale output frequency can be scaled by writing to the CFNUM and CFDEN reg-
isters—see
Energy To Frequency Conversion.
This provides the ground reference for the digital circuitry in the ADE7754, i.e. multi-
plier, filters and digital-to-frequency converter. Because the digital return currents in
the ADE7754 are small, it is acceptable to connect this pin to the analog ground plane
of the whole system. However high bus capacitance on the DOUT pin may result in
noisy digital current which could affect performance.
Digital power supply. This pin provides the supply voltage for the digital circuitry in
the ADE7754. The supply voltage should be maintained at 5V ± 5% for specified op-
eration. This pin should be decoupled to DGND with a 10μF capacitor in parallel with
a ceramic 100nF capacitor.
Analog power supply. This pin provides the supply voltage for the analog circuitry in
the ADE7754. The supply should be maintained at 5V ± 5% for specified operation.
Every effort should be made to minimize power supply ripple and noise at this pin by
the use of proper decoupling. The typical performance graphs in this data sheet show
the power supply rejection performance. This pin should be decoupled to AGND with a
10μF capacitor in parallel with a ceramic 100nF capacitor.
Analog inputs for current channel. This channel is intended for use with the current
transducer and is referenced in this document as the current channel. These inputs are
fully differential voltage inputs with maximum differential input signal levels of ±0.5V,
±0.25V and ±0.125V, depending on the gain selections of the internal PGA -See
Analog
Inputs
.
All inputs have internal ESD protection circuitry, and in addition an overvoltage of
±6V can be sustained on these inputs without risk of permanent damage.
This pin provides the ground reference for the analog circuitry in the ADE7754, i.e.
ADCs, temperature sensor, and reference. This pin should be tied to the analog ground
plane or the quietest ground reference in the system. This quiet ground reference
should be used for all analog circuitry, e.g. anti aliasing filters, current and voltage
transducers etc. In order to keep ground noise around the ADE7754 to a minimum, the
quiet ground plane should only connected to the digital ground plane at one point. It is
acceptable to place the entire device on the analog ground plane.
This pin provides access to the on-chip voltage reference. The on-chip reference has a
nominal value of 2.4V ± 8% and a typical temperature coefficient of 30ppm/°C. An
external reference source may also be connected at this pin. In either case this pin
should be decoupled to AGND with a 1μF ceramic capacitor.
Analog inputs for the voltage channel. This channel is intended for use with the voltage
transducer and is referenced as the voltage channel in this document. These inputs are
single-ended voltage inputs with maximum signal level of ±0.5V with respect to V
N
for
specified operation. These inputs are voltage inputs with maximum differential input
signal levels of ±0.5V, ±0.25V and ±0.125V, depending on the gain selections of the
internal PGA - see
Analog Inputs
.
All inputs have internal ESD protection circuitry, and in addition an over voltage of
±6V can be sustained on these inputs without risk of permanent damage.
Reset pin for the ADE7754. A logic low on this pin will hold the ADCs and digital
circuitry (including the Serial Interface) in a reset condition.
Interrupt Request Output. This is an active low open drain logic output. Maskable
interrupts include: Active Energy Register at half level, Apparent Energy Register at
half level, and waveform sampling up to 26kSPS. See
ADE7754 Interrupts
.
2
DGND
3
DV
DD
4
AV
DD
5,6;
7,8;
9,10
I
AP
, I
AN
;
I
BP
, I
BN
;
I
CP
, I
CN
11
AGND
12
REF
IN/OUT
13, 14
15, 16
V
N
, V
CP
,
V
BP
, V
AP
17
RESET
18
IRQ
相關PDF資料
PDF描述
ADE7754ARRL ADE7754
ADE7755AN-REF Energy Metering IC with Pulse Output
ADE7755ARSRL Energy Metering IC with Pulse Output
ADE7755 Energy Metering IC with Pulse Output
ADE7755ARS Energy Metering IC with Pulse Output
相關代理商/技術參數
參數描述
ADE7754ARRL 制造商:Analog Devices 功能描述:Energy Measurement 24-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:THREE PHASE ENERGY METER IC W/WATT & VA - Bulk
ADE7754ARZ 功能描述:IC ENERGY METERING 3PHASE 24SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7754ARZRL 功能描述:IC ENERGY METERING 3PHASE 24SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 能量測量 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:*
ADE7755 制造商:AD 制造商全稱:Analog Devices 功能描述:Energy Metering IC with Pulse Output
ADE7755AARSRL 制造商:Analog Devices 功能描述:ENERGY METERING IC WITH P - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*