參數資料
型號： AD9991KCPRL
廠商： ANALOG DEVICES INC
元件分類： 消費家電
英文描述： 10-Bit CCD Signal Processor with Precision Timing Generator
中文描述： SPECIALTY CONSUMER CIRCUIT, QCC56
封裝： 8 X 8 MM, MO-220-VLLD-2, LFCSP-56
文件頁數： 26/60頁
文件大?。?/td> 826K
代理商： AD9991KCPRL
AD9991
–26–
SHUTTER TIMING CONTROL
The CCD image exposure time is controlled by the substrate
clock signal (SUBCK), which pulses the CCD substrate to clear
out accumulated charge. The AD9991 supports three types of
electronic shuttering: normal shutter, high precision shutter,
and low speed shutter. Along with the SUBCK pulse placement,
the AD9991 can accommodate different readout configurations
to further suppress the SUBCK pulses during multiple field
readouts. The AD9991 also provides programmable outputs to
control an external mechanical shutter (MSHUT), strobe/flash
(STROBE), and the CCD bias select signal (VSUB).
Normal Shutter Operation
By default, the AD9991 is always operating in the normal shutter
configuration in which the SUBCK signal is pulsing in every VD
field (see Figure 26). The SUBCK pulse occurs once per line,
and the total number of repetitions within the field will determine
the length of the exposure time. The SUBCK pulse polarity
and toggle positions within a line are programmable using the
SUBCKPOL and SUBCK1TOG registers (see Table XI).
The number of SUBCK pulses per field is programmed in the
SUBCKNUM register (addr. 0x63).
As shown in Figure 26, the SUBCK pulses will always begin
in the line following the SG active line, which is specified in
the SGACTLINE registers for each field. The SUBCKPOL,
SUBCK1TOG, SUBCK2TOG, SUBCKNUM, and SUBCK-
SUPPRESS registers are updated at the start of the line after the
sensor gate line, as described in the Serial Update section.
High Precision Shutter Operation
High precision shuttering is used in the same manner as nor-
mal shuttering, but uses an additional register to control the
very last SUBCK pulse. In this mode, the SUBCK still pulses
once per line, but the last SUBCK in the field will have an
additional SUBCK pulse whose location is determined by the
SUBCK2TOG register, as shown in Figure 27. Finer resolution
of the exposure time is possible using this mode. Leaving the
SUBCK2TOG register set to max value (0xFFFFFF) will disable
the last SUBCK pulse (default setting).
Low Speed Shutter Operation
Normal and high precision shutter operations are used when
the exposure time is less than one field long. For long exposure
times greater than one field interval, low speed shutter opera-
tion is used. The AD9991 uses a separate exposure counter to
achieve long exposure times. The number of fields for the low
speed shutter operation is specified in the EXPOSURE register
(addr. 0x62). As shown in Figure 28, this shutter mode will
suppress the SUBCK and VSG outputs for up to 4095 fields
(VD periods). The VD and HD outputs may be suppressed
during the exposure period by programming the VDHDOFF
register to 1.
To generate a low speed shutter operation, it is necessary to trig-
ger the start of the long exposure by writing to the TRIGGER
register bit D3. When this bit is set High, the AD9991 will begin
an exposure operation at the next VD edge. If a value greater than
zero is specified in the EXPOSURE register, the AD9991 will
suppress the SUBCK output on subsequent fields.
VD
SUBCK
SUBCK PROGRAMMABLE SETTINGS:
1. PULSE POLARITY USING THE SUBCKPOL REGISTER
2. NUMBER OF PULSES WITHIN THE FIELD USING THE SUBCKNUM REGISTER (SUBCKNUM = 3 IN THE ABOVE FIGURE)
3. PIXEL LOCATION OF PULSE WITHIN THE LINE AND PULSEWIDTH PROGRAMMED USING SUBCK1 TOGGLE POSITION REGISTER
t
EXP
VSG
HD
t
EXP
Figure 26. Normal Shutter Mode
VD
SUBCK
NOTES
1. SECOND SUBCK PULSE IS ADDED IN THE LAST SUBCK LINE.
2. LOCATION OF 2ND PULSE IS FULLY PROGRAMMABLE USING THE SUBCK2 TOGGLE POSITION REGISTER.
VSG
HD
t
EXP
t
EXP
Figure 27. High Precision Shutter Mode
REV. 0
相關PDF資料
PDF描述
AD9991KCP 10-Bit CCD Signal Processor with Precision Timing Generator
AD9991 10-Bit CCD Signal Processor with Precision Timing Generator
AD9992 12-Bit CCD Signal Processor with Precision Timing Generator
AD9992BBCZ 12-Bit CCD Signal Processor with Precision Timing Generator
AD9992BBCZRL 12-Bit CCD Signal Processor with Precision Timing Generator
相關代理商/技術參數
參數描述
AD9991KCPZ 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9991KCPZRL 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
AD9992 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator
AD9992_07 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator
AD9992BBCZ 功能描述:IC CCD SGNL PROC 12BIT 105CSPBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*