- 您現在的位置：買賣IC網 > PDF目錄10599 > AD9984AKSTZ-170 (Analog Devices Inc)IC DISPLAY 10BIT 170MSPS 80LQFP PDF資料下載
參數資料
| 型號： | AD9984AKSTZ-170 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DISPLAY 10BIT 170MSPS 80LQFP |
| 標準包裝： | 1 |
| 類型： | 接口 |
| 應用： | 顯示器，處理，電視 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9984A
Rev. 0 | Page 26 of 44
Hex
Address
Read/Write,
Read Only
Bits
Default
Value
Register Name
Description
3
**** 0***
Red Clamp Select.
0 = Clamp the red channel to ground.
1 = Clamp the red channel to midscale.
2
**** *0**
Green Clamp Select.
0 = Clamp the green channel to ground.
1 = Clamp the green channel to midscale.
1
**** **0*
Blue Clamp Select.
0 = Clamp the blue channel to ground.
1 = Clamp the blue channel to midscale.
0
**** ***0
Must be set to 0 for proper operation.
0x19
R/W
7:0
0000 1000
Clamp Placement
Places the clamp signal an integer number of clock periods after the
trailing edge of the Hsync signal.
0x1A
R/W
7:0
0010 0000
Clamp Duration
Number of clock periods that the clamp signal is actively clamping.
0x1B
R/W
7
0*** ****
Clamp and Offset
Clamp Polarity Override.
0 = The chip selects the clamp polarity.
1 = The polarity of the clamp signal is set by Reg. 0x1B, Bit 6.
6
*1** ****
Clamp Polarity. This bit is used only if Reg. 0x1B, Bit 7 is set to 1.
0 = Clamp polarity is negative.
1 = Clamp polarity is positive.
5
**0* ****
Auto-Offset Enable.
0 = Auto-offset is disabled.
1 = Auto-offset is enabled (offsets become the desired clamp code).
4:3
***1 1***
Auto-Offset Update Frequency. This selects how often the auto-
offset circuit operates.
00 = Every 3 clamps.
01 = Every 48 clamps.
10 = Every 192 clamps.
11 = Every 3 Vsync periods.
2:0
**** *011
Must be written to default (011) for proper operation.
0x1C
R/W
7:0
1111 1111
Test Register 0
Must be set to 0xFF for proper operation.
0x1D
R/W
7:3
0111 1***
SOG Control
SOG Slicer Comparator Threshold. Sets the voltage level of SOG slicer’s
comparator.
2
**** *0**
SOGOUT Polarity. Sets the polarity of the signal on the SOGOUT pin.
0 = SOGOUT polarity is negative.
1 = SOGOUT polarity is positive.
1:0
**** **00
SOGOUT Select.
00 = Raw SOGINx.
01 = Raw HSYNCx.
10 = Regenerated Hsync from sync filter.
11 = Filtered Hsync from sync filter.
0x1E
R/W
7
*** ****
Input and Power
Control
Channel Select Override.
0 = The chip determines which input channels to use.
1 = The input channel selection is determined by Reg. 0x1E, Bit 6.
6
*0** ****
Channel Select. This is used only if Reg. 0x1E, Bit 7 is set to 1, or if
syncs are present on both channels.
0 = Channel 0 syncs and data are selected.
1 = Channel 1 syncs and data are selected.
5
**1* ****
Programmable Bandwidth.
0 = Low analog input bandwidth (~7 MHz).
1 = High analog input bandwidth (~300 MHz).
4
***1 ****
Power-Down Control Select.
0 = Manual power-down control.
1 = Auto power-down control.
3
**** 0***
Power-Down.
0 = Normal operation.
1 = Power-down.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BTN-MX-F3 | CONVERTER MOD DC/DC 18.5V 75W |
| ADV7186BBCZ-TL-RL | IC VIDEO DECODER 196CSPBGA |
| VI-2WH-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
| VE-BTN-MX-F2 | CONVERTER MOD DC/DC 18.5V 75W |
| T 3507 009 | CONN FMALE RCPT 8PS FRONT PNL MT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9984APCBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
| AD9984KSTZ-110 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9984KSTZ-140 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9984KSTZ-170 | 制造商:Analog Devices 功能描述: |
| AD9985 | 制造商:AD 制造商全稱:Analog Devices 功能描述:110 MSPS/140 MSPS Analog Interface for Flat Panel Displays |
發布緊急采購，3分鐘左右您將得到回復。