參數資料
型號： AD9888KS-205
廠商： ANALOG DEVICES INC
元件分類： 消費家電
英文描述： TRI N RECP M J/N 2-13
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP128
封裝： PLASTIC, MQFP-128
文件頁數： 29/32頁
文件大?。?/td> 249K
代理商： AD9888KS-205
REV. A
AD9888
–29–
analog supply voltage. This can be mitigated by regulating the
analog supply, or at least PVd, from a different, cleaner, power
source (for example, from a 12 V supply).
It is also recommended to use a single ground plane for the
entire board. Experience has repeatedly shown that the noise
performance is the same or better with a single ground plane.
Using multiple ground planes can be detrimental because each
separate ground plane is smaller, and long ground loops can result.
In some cases, using separate ground planes is unavoidable. For
those cases, it is recommended to at least place a single ground
plane under the AD9888. The location of the split should be at
the receiver of the digital outputs. For this case it is even more
important to place components wisely because the current loops
will be much longer (current takes the path of least resistance).
An example of a current loop: power plane => AD9888 =>
digital output trace => digital data receiver => digital ground
plane => analog ground plane.
PLL
Place the PLL loop filter components as close to the FILT pin
as possible.
Do not place any digital or other high-frequency traces near these
components.
Use the values suggested in the data sheet with 10% tolerances
or less.
Outputs (Both Data and Clocks)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, requiring more
current and causing more internal digital noise.
Shorter traces reduce the possibility of reflections.
Adding a series resistor of value 50
–200
can suppress
reflections, reduce EMI, and reduce the current spikes inside
the AD9888. If series resistors are used, place them as close to
the AD9888 pins as possible (although try not to add vias or extra
length to the output trace in order to get the resistors closer).
If possible, limit the capacitance that each of the digital outputs
drives to less than 10 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance will
increase the current transients inside of the AD9888 creating
more digital noise on its power supplies.
Digital Inputs
The digital inputs on the AD9888 were designed to work with
3.3 V signals, but are tolerant of 5.0 V signals. So, no extra
components need to be added if using 5.0 V logic.
Any noise that gets onto the Hsync input trace will add jitter to
the system. Therefore, minimize the trace length and do not run
any digital or other high-frequency traces near it.
Voltage Reference
Bypass with a 0.1
μ
F capacitor. Place as close to the AD9888
pin as possible. Make the ground connection as short as possible.
相關PDF資料
PDF描述
AD9891 CCD Signal Processors with Precision Timing⑩ Generator
AD9895 CCD Signal Processors with Precision Timing⑩ Generator
AD9891KBC CCD Signal Processors with Precision Timing⑩ Generator
AD9895KBC CCD Signal Processors with Precision Timing⑩ Generator
AD9911BCPZ 500 MSPS Direct Digital Synthesizer with 10-Bit DAC
相關代理商/技術參數
參數描述
AD9888KSZ-100 功能描述:IC FLAT PANEL INTERFACE 128-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9888KSZ-140 功能描述:IC FLAT PANEL INTERFACE 128-MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9888KSZ-140 制造商:Analog Devices 功能描述:IC ANALOG INTERFACE
AD9888KSZ-170 功能描述:IC ANALOG INTRFC 170MSPS 128MQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 特色產品:NXP - I2C Interface 標準包裝:1 系列:- 應用:2 通道 I²C 多路復用器 接口:I²C，SM 總線 電源電壓:2.3 V ~ 5.5 V 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:剪切帶 (CT) 安裝類型:表面貼裝 產品目錄頁面:825 (CN2011-ZH PDF) 其它名稱:568-1854-1
AD9888KSZ-170 制造商:Analog Devices 功能描述:TV / Video IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*