- 您現在的位置：買賣IC網 > PDF目錄373962 > AD9244BST-65 (ANALOG DEVICES INC) 14-Bit, 40/65 MSPS Monolithic A/D Converter PDF資料下載
參數資料
| 型號： | AD9244BST-65 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 14-Bit, 40/65 MSPS Monolithic A/D Converter |
| 中文描述： | 1-CH 14-BIT FLASH METHOD ADC, PARALLEL ACCESS, PQFP48 |
| 封裝： | MS-026-BBC, LQFP-48 |
| 文件頁數： | 20/36頁 |
| 文件大?。?/td> | 1845K |
| 代理商： | AD9244BST-65 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
REV. A
–20–
AD9244
Clock Input Considerations
The analog input is sampled on the rising edge of the clock.
Timing variations, or jitter, on this edge causes the sampled
input voltage to be in error by an amount proportional to the
slew rate of the input signal and to the amount of the timing
variation. Thus, to maintain the excellent high frequency SFDR
and SNR characteristics of the AD9244, it is essential that the
clock edge be kept as clean as possible.
The clock should be treated like an analog signal. Clock drivers
should not share supplies with digital logic or noisy circuits. The
clock traces should not run parallel to noisy traces. Using a pair
of symmetrically routed, differential clock signals can help to
provide immunity from common-mode noise coupled from the
environment.
The clock receiver functions like a differential comparator. At
the CLK inputs, a slowly changing clock signal will result in
more jitter than a rapidly changing one. Driving the clock with
a low amplitude sine wave input is not recommended. Running
a high speed clock through a divider circuit will provide a fast
rise/fall time, resulting in the lowest jitter in most systems.
CLK+
CLK–
AD9244
Figure 15a. Differential Clock Input—DC-Coupled
CLK+
CLK–
AD9244
AGND
0.1 F
1.6V
Figure 15b. Single-Ended Clock Input
—
DC-Coupled
CLK+
CLK–
AD9244
AGND
Figure 15c. Single-Ended Input
—
Retains Pin
Compatibility with AD9226
CLOCK OVERVIEW
The AD9244 has a flexible clock interface that accepts either a
single-ended or differential clock. An internal bias voltage facilitates
ac coupling using two external capacitors. To remain backward
compatible with the single-pin clock scheme of the AD9226, the
AD9244 can be operated with a dc-coupled, single-pin clock by
grounding the CLK
–
pin and driving CLK+.
When the CLK
–
pin is not grounded, the CLK+ and CLK
–
pins
function as a differential clock receiver. When CLK+ is greater
than CLK
–
, the SHA is in hold mode; when CLK+ is less than
CLK
–
, the SHA is in track mode (see timing in Figure 14). The
rising edge of the clock (CLK+
–
CLK
–
) switches the SHA from
track to hold and timing jitter on this transition should be mini-
mized, especially for high frequency analog inputs.
It is often difficult to maintain a 50% duty cycle to the ADC,
especially when driving the clock with a single-ended or sine
wave input. To ease the constraint of providing an accurate
50% clock, the ADC has an optional internal duty cycle stabilizer
(DCS) that allows the rising clock edge to pass through with
minimal jitter and interpolates the falling edge, independent of
the input clock falling edge. The DCS is described in greater
detail in a later section.
Clock Input Modes
Figures 15a to 15e illustrate the modes of operation of the clock
receiver. Figure 15a shows a differential clock directly coupled to
CLK+ and CLK
–
. In this mode, the common mode of the CLK+
and CLK
–
signals should be close to 1.6 V. Figure 15b illustrates
a single-ended clock input. The capacitor decouples the internal
bias voltage on the CLK
–
pin (about 1.6 V), establishing a threshold
for the CLK+ pin. Figure 15c provides backward compatibility
with the AD9226. In this mode, CLK
–
is grounded and the
threshold for CLK+ is 1.5 V. Figure 15d shows a differential clock
ac-coupled by connecting through two capacitors. AC coupling
a single-ended clock can also be accomplished using the circuit
in Figure 15e.
When using the differential clock circuits of Figure 15a or
Figure 15d, if CLK
–
drops below 250 mV, the mode of the clock
receiver may change, causing conversion errors. It is essential
that CLK
–
remain above 250 mV when the clock is ac-coupled
or dc-coupled.
CLK–
CLK+
CLK–
CLK+
SHA IN
HOLD
SHA IN
TRACK
Figure 14. SHA Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9244BST-40 | 14-Bit, 40/65 MSPS Monolithic A/D Converter |
| AD9245 | 14-Bit, 80 MSPS, 3 V A/D Converter |
| AD9245BCP-80 | 14-Bit, 80 MSPS, 3 V A/D Converter |
| AD9245BCPRL7-80 | 14-Bit, 80 MSPS, 3 V A/D Converter |
| AD9245BCPZ-80 | 14-Bit, 80 MSPS, 3 V A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9244BSTRL-40 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 40/65 MSPS Monolithic A/D Converter |
| AD9244BSTRL-65 | 制造商:Analog Devices 功能描述:Single ADC Pipelined 65Msps 14-bit Parallel 48-Pin LQFP T/R |
| AD9244BSTZ40 | 制造商:Analog Devices 功能描述: |
| AD9244BSTZ-40 | 功能描述:IC ADC 14BIT 40MSPS 48-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| AD9244BSTZ-401 | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 40 MSPS/65 MSPS A/D Converter |
發布緊急采購，3分鐘左右您將得到回復。