- 您現在的位置：買賣IC網 > PDF目錄10308 > AD7939BSUZ-REEL7 (Analog Devices Inc)IC ADC 10BIT 8CH PARALL 32TQFP PDF資料下載
參數資料
| 型號： | AD7939BSUZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/36頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT 8CH PARALL 32TQFP |
| 標準包裝： | 500 |
| 位數： | 10 |
| 采樣率（每秒）： | 1.5M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 13.5mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP |
| 供應商設備封裝： | 32-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 8 個單端，單極；4 個差分，單極；4 個偽差分，單極；7 偽差分，單極 |
| 配用： | EVAL-AD7939CBZ-ND - BOARD EVALUATION FOR AD7939CBZ |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Data Sheet
AD7938/AD7939
Rev. C | Page 15 of 36
ON-CHIP REGISTERS
The AD7938/AD7939 have two on-chip registers that are
necessary for the operation of the device. These are the control
register, which is used to set up different operating conditions,
and the shadow register, which is used to program the analog
input channels to be converted.
CONTROL REGISTER
The control register on the AD7938/AD7939 is a 12-bit, write-
only register. Data is written to this register using the CS and
WR pins. The control register is shown in Table 7 and the
functions of the bits are described in Table 8. At power up, the
default bit settings in the control register are all 0s.
Table 7. Control Register Bits
MSB
LSB
DB11
DB10
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
PM1
PM0
CODING
REF
ADD2
ADD1
ADD0
MODE1
MODE0
SHDW
SEQ
RANGE
Table 8. Control Register Bit Function Description
Bit No.
Mnemonic
Description
11, 10
PM1, PM0
Power Management Bits. These two bits are used to select the power mode of operation. The user can choose
between either normal mode or various power-down modes of operation, as shown in Table 9.
9
CODING
This bit selects the output coding of the conversion result. If this bit is set to 0, the output coding is straight
(natural) binary. If this bit is set to 1, the output coding is twos complement.
8
REF
This bit selects whether the internal or external reference is used to perform the conversion. If this bit is Logic 0, an
external reference should be applied to the VREF pin. If this bit is Logic 1, the internal reference is selected. See the
Reference section.
7 to 5
ADD2 to
ADD0
These three address bits are used to either select which analog input channel is converted in the next conversion if
the sequencer is not used, or to select the final channel in a consecutive sequence when the sequencer is used, as
described in Table 11. The selected input channel is decoded as shown in Table 10.
4, 3
MODE1,
MODE0
The two mode pins select the type of analog input on the eight VIN pins. The AD7938/AD7939 can have either eight
single-ended inputs, four fully differential inputs, four pseudo differential inputs, or seven pseudo differential
inputs. See Table 10.
2
SHDW
The SHDW bit in the control register is used in conjunction with the SEQ bit to control the sequencer function and
access the SHDW register. See Table 11.
1
SEQ
The SEQ bit in the control register is used in conjunction with the SHDW bit to control the sequencer function and
access the SHDW register. See Table 11.
0
RANGE
This bit selects the analog input range of the AD7938/AD7939. If it is set to 0, the analog input range extends from
0 V to VREF. If it is set to 1, the analog input range extends from 0 V to 2 × VREF. When this range is selected, VDD must
be 4.75 V to 5.25 V if a 2.5 V reference is used; otherwise, care must be taken to ensure that the analog input remains
within the supply rails. See the Analog Inputs section for more information.
Table 9. Power Mode Selection Using the Power Management Bits in the Control Register
PM1
PM0
Mode
Description
0
Normal Mode
When operating in normal mode, all circuitry is fully powered up at all times.
0
1
Autoshutdown
When operating in autoshutdown mode, the AD7938/AD7939 enter full shutdown mode at the end of
each conversion. In this mode, all circuitry is powered down.
1
0
Autostandby
When the AD7938/AD7939 enter this mode, all circuitry is powered down except for the reference and
reference buffer. This mode is similar to autoshutdown mode, but it allows the part to power up in 7 s (or
600 ns if an external reference is used). See the Power Modes of Operation section for more information.
1
Full Shutdown
When the AD7938/AD7939 enter this mode, all circuitry is powered down. The information in the control
register is retained.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27508E24B35AB | CONN HSG RCPT 128POS BOX MT PIN |
| AD7266BCPZ-REEL | IC ADC 12BIT 3CHAN 2MSPS 32LFCSP |
| VE-BNP-IX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| AD7799BRUZ-REEL | IC ADC 24BIT 3CH LP 16-TSSOP |
| VE-BNP-IW-B1 | CONVERTER MOD DC/DC 13.8V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7940 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3mW, 100kSPS, 14-Bit ADC in 6-Lead SOT-23 |
| AD7940BRJ | 制造商:Analog Devices 功能描述:100 KSPS, 14_BIT ADC SOT 23 PKG I.C. - Bulk |
| AD7940BRJ-R2 | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 14-bit Serial 6-Pin SOT-23 T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 100KSPS 14BIT SERL 6PIN SOT-23 - Tape and Reel |
| AD7940BRJ-REEL7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD7940BRJZ-REEL7 | 功能描述:IC ADC 14BIT 100KSPS SOT-23-6 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。