These channels" />
參數資料
型號: AD7877ACBZ-REEL7
廠商: Analog Devices Inc
文件頁數: 13/45頁
文件大?。?/td> 0K
描述: IC CTRLR TOUCH SCREEN 25-WLCSP
標準包裝: 1
類型: 電阻
觸摸面板接口: 4 線
輸入數/鍵: 1 TSC
分辨率(位): 12 b
評估套件: 可供
數據接口: 串行,SPI?
數據速率/采樣率 (SPS,BPS): 125k
電壓基準: 外部,內部
電源電壓: 2.7 V ~ 5.25 V
電流 - 電源: 1µA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 25-UFBGA,WLCSP
供應商設備封裝: 25-WLCSP
包裝: 標準包裝
產品目錄頁面: 779 (CN2011-ZH PDF)
配用: EVAL-AD7877EBZ-ND - BOARD EVALUATION FOR AD7877
其它名稱: AD7877ACBZ-REEL7DKR
Data Sheet
AD7877
Rev. D | Page 19 of 44
AUXILIARY INPUTS
The AD7877 has three auxiliary analog inputs, AUX1 to AUX3.
These channels have a full-scale input range from 0 V to VREF.
The ADC channel addresses for AUX1 to AUX3 are 0011b,
0100b, and 0101b, and the results are stored in Register 10011b,
Register 10100b, and Register 10101b. These pins can also be
reconfigured as general-purpose logic inputs/outputs, as
described in the GPIO Configuration section.
LIMIT COMPARISON
The AUX1 measurement, the two battery measurements, and
the TEMP1 measurement can all be compared with high and
low limits, and an out-of-limit result that generates an alarm
output at the ALERT pin. The limits are stored in registers with
addresses from 00100b to 01011b. After a measurement from
any one of the four channels is converted, it is compared with
the corresponding high and low limits. An out-of-limit result
sets one of the status bits in the alert status/enable register. For
details on these and other registers, see the Register Maps and
Detailed Register Descriptions sections. For details on writing
and reading data, see the Serial Interface section.
As described in the Single Conversion Method section, the
temperature comparison is made using the result of the TEMP1
measurement, that is, the diode forward voltage. Because the
temperature coefficient of the diode is known but the actual
forward voltage can have a wide tolerance, it is not possible
to program the high and low limit registers with predeter-
mined values.
Instead, it is necessary to calibrate the temperature measure-
ment, calculate the TEMP1 readings at the high and low limit
temperatures, and then program those values into the limit
registers, as follows:
1. Calculate
LSB per degree = 2.1 mV/(VREF/4096).
2. Save the calibration reading DCAL at the calibration
temperature, TCAL.
3. Subtract TCAL from limit temperatures THIGH and TLOW
to get the difference in degrees between the limit
temperatures and the calibration temperature.
4. Multiply this value by LSB per degree to obtain the
value in LSBs.
5. Add these values to the digital value at the calibration
temperature to get the digital high and low limit values.
Example:
The internal 2.5 V reference is used.
1. THIGH = +65°C and TLOW = 10°C.
2. LSB per degree = 2.1 × 103/(2.5/4096) = 3.44.
3. DCAL = 983 decimal at 25°C.
4. DHIGH = (65 25) × 3.44 + 983 = 845.
5. DLOW = (10 25) × 3.44 + 983 = 1103.
相關PDF資料
PDF描述
MS27484T22A35SB CONN PLUG 100POS STRAIGHT W/SCKT
MS27468T25B35SD CONN RCPT 128POS JAM NUT W/SCKT
MS27468E25B35SD CONN RCPT 128POS JAM NUT W/SCKT
MAX11811ETP+ IC TOUCH SCREEN 12BIT I2C 20TQFN
MXB7843EEE+ IC CNTRLR TOUCH RES 16QSOP
相關代理商/技術參數
參數描述
AD7877ACP 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk
AD7877ACP-500RL7 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER
AD7877ACP-REEL 制造商:AD 制造商全稱:Analog Devices 功能描述:Touch Screen Controller
AD7877ACP-REEL7 制造商:Analog Devices 功能描述:TOUCH SCREEN CONTROLLER
AD7877ACPZ 制造商:Analog Devices 功能描述:TOUCH SCREEN CNTRLR 32LFCSP - Bulk