2006 Teridian Semiconductor Corporation Rev." />
參數資料
型號： 78P2351-IGTR/F
廠商： Maxim Integrated Products
文件頁數： 27/42頁
文件大?。?/td> 0K
描述： LINE INTERFACE UNIT 100-LQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 1,000
類型： 線路接口裝置（LIU）
驅動器/接收器數： 1/1
規程： E4，OC-3，STM1-E
電源電壓： 3.15 V ~ 3.45 V
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-LQFP（16x16）
包裝： 帶卷 (TR)
78P2351
Single Channel
OC-3/ STM1-E/ E4 LIU
Page: 33 of 42
2006 Teridian Semiconductor Corporation
Rev. 2.4
ELECTRICAL SPECIFICATIONS (continued)
(Note 1)
0.60
0.55
0.50
0.45
0.40
0.05
-0.05
-0.50
-0.55
-0.60
-0.45
-0.40
(Note 1)
Nominal
Zero Level
(Note 2)
6.43ns
0.1ns
1ns
1.608ns
1ns
Nominal
Pulse
V
3.215ns
1.2ns
3.215ns
1.608ns
1ns
0.5ns
Note 1 – The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to fall into
the shaded area bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by more than
0.05V.
Note 2 – For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01
F, to the input of
the oscilloscope used for measurements. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input
signal. With the signal then applied, the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any
such adjustment should be the same for both masks and should not exceed
±0.05V. This may be checked by removing the input signal again
and verifying that the trace lies with
±0.05V of the nominal zero level of the masks.
Note 3 – Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding or
succeeding pulses, with both pulse masks fixed in the same relation to a common timing reference, i.e. with their nominal start and finish
edges coincident. The masks allow for HF jitter caused by intersymbol interference in the output stage, but not for jitter present in the timing
signal associated with the source of the interface signal. When using an oscilloscope technique to determine pulse compliance with the mask,
it is important that successive traces of the pulses overlay in order to suppress the effects of low frequency jitter. This can be accomplished by
several techniques [e.g. a) triggering the oscilloscope on the measured waveform or b) providing both the oscilloscope and the pulse output
circuits with the same clock signal].
Note 4 – For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed
2ns.
Note 5 –The inverse pulse will have the same characteristics, noting that the timing tolerance at the level of the negative and positive
transitions are
± 0.1ns and ±0.5ns respectively.
Figure 15 – Mask of a Pulse corresponding to a binary One in STM-1/STS-3 mode
相關PDF資料
PDF描述
78P2351R-IMR/F IC LIU NRZ-CMI CONV 155M 56-QFN
78P2352-IELR/F IC LIU SDH SONET 2CH 128-LQFP
78Q2120C09-64CGTR/F TXRX 10/100 BASE 3.3V 64-LQFP
78Q2133/F TXRX 10/100 MDIX 3.3V IND 32-QFN
78Q8392LA03-28CHR/F TXRX 10BASE 2/5 ETH COAX 28-PLCC
相關代理商/技術參數
參數描述
78P2351R 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter
78P2351R-DB 功能描述:界面開發工具 78P2351R Demo Brd RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
78P2351R-IM 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter
78P2351R-IM/F 功能描述:接口 - 專用 Serial 155M NRZ to CMI Converter RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
78P2351R-IMR 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Serial 155M NRZ to CMI Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*