參數資料
型號： ZPSD502B1V
英文描述： Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
中文描述： 現場可編程微控制器外圍設備（可編程邏輯，零功耗，16K的位的SRAM，40余個可編程輸入/輸出，通用PLD的有61個輸入）
文件頁數： 63/142頁
文件大?。?/td> 786K
代理商： ZPSD502B1V
ZPSD5XX Famly
7-63
Power
Management
Unit
(Cont.)
Oher Power Saving Options
The ZPSD5XX provides additional power saving options. These options, except the SRAM
Standby Mode, can be enabled/disabled by setting up the corresponding bit in the PMMR.
J
EPROM
The EPROM power consumption in the PSD is controlled by bit 3 in the
PMMR0 – EPROM CMiser. Upon reset the CMiser bit is OFF. This will cause the
EPROM to be ON at all times as long as CSI is enabled (low). The reason this mode is
provided is to reduce the access time of the EPROM by 10 ns relative to the low power
condition when CMiser is ON. If CSI is disabled (high) the EPROM will be deselected
and will enter standby mode (OFF) overriding the state of the CMiser.
If CMiser is set (ON) then the EPROM will enter the standby mode when not selected.
This condition can take place when CSI is high or when CSI is low and the EPROM is
not accessed. For example, if the MCU is accessing the SRAM, the EPROM will be
deselected and will be in low power mode.
An additional advantage of the CMiser is achieved when the PSD is configured in the
by 8 mode (8 bit data bus). In this case an additional power savings is achieved in the
EPROM (and also in the SRAM) by turning off 1/2 of the array even when the EPROM
is accessed (the array is divided internally into odd and even arrays).
The power consumption for the different EPROM modes is given in the DC
Characteristics table under I
CC
(DC) EPROM Adder.
J
SRAM Standby Mode
The SRAM has a dedicated supply voltage V
STBY
that can be used to connect a
battery. When V
CC
becomes lower than V
STBY
–0.6 then the ZPSD5XX will automatically
connect the V
STBY
as a power source to the SRAM. The SRAM Standby Current (I
STBY
)
is typically 0.5 μA.
SRAM data retention voltage V
DF
is 2 V minimum.
J
Zero Power ZPLD
ZPLD power/speed is controlled by the ZPLD_Turbo bit (bit 4) in the PMMR0. After
reset the ZPLD is in Turbo mode and runs at full power and speed. By setting the bit to
“1”, the Turbo mode is disabled and the ZPLD is consuming Zero Power current if the
inputs are not switching for an extended time of 100 ns. The propagation delay time will
be increased by 10ns after the Turbo bitis set to “1” (turned off) if the inputs change at a
frequency of less than 15 MHz.
See page 7-142
for CMiser Errata.
相關PDF資料
PDF描述
ZPSD512B1 Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
ZPSD512B1V Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
ZPSD513B1 Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
ZPSD513B1V Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
ZPSD501B1 Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入)
相關代理商/技術參數
參數描述
ZPSD503B1-C-15L 制造商:WSI 功能描述:
ZPSD512B1-C-90UI 制造商:WSI 功能描述:
ZPSD513B1-C-15L 制造商:WSI 功能描述:
ZPSD602E1-15L 制造商:WSI 功能描述:
ZPSD611E1-15J 制造商:WSI 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*