- 您現在的位置：買賣IC網 > PDF目錄382772 > ZPSD413A2 Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有59個輸入) PDF資料下載
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
ZPSD4XX Famly
5-76
Reset Input
The reset input to the ZPSD4XX (RESET) is an active low signal which resets some
of the internal devices and configuration registers. The Timing Diagram in the AC/DC
characterization section shows the reset signal timing requirement. The active low range
has a minimum T1 duration. After the rising edge of RESET, the ZPSD4XX remains in
reset during T2 range. (See Figure 48). The ZPSD4XX must be reset at power up before it
can be used.
ZPLDand Memory During Reset
While the Reset Input is active, the ZPLD generates outputs as defined in the PSDabel
equations. The EPROM and SRAM blocks respond to the microcontroller bus cycle during
reset, but the data is not guaranteed.
Register Values During and After Reset
Table 24 summarizes the status of the volatile register values during and after reset.
The default values of the volatile registers are “0” after reset.
ZPLDMacrocell Initialization
The D flip flops in the macrocells in the GPLD can be cleared by:
J
A product term (.RE) defined by the user in PSDabel, or
J
The MACRO-RST (Reset) input, enabled and defined in PSDabel.
Register Name
Device
Reset State
Control
Port A, B, C, D, E
Set to “0”
(Address Out Mode)
Data Out
(data or address)
Port A, B, C, D, E
Set to “0”
Direction
Port A, B, C, D, E
Set to “0” – Input Mode
Open Drain
Port C, D
Set to “0” – CMOS Outputs
Page Register
Page Logic
Set to “0”
PMMR0, PMMR1
Power Management Unit
Set to “0”
VM
Volatile Memory
Set to “0”
System
Configuration
(Cont.)
Table 24. Registers Reset Values
Port Configuration
Reset
Stand-by Mode
Port I/O
Input
Unchanged
ZPLD Output
Active
Depend on Inputs to the ZPLD
Address Out
Tri-stated
Not Defined
Data Port
Tri-stated
Tri-stated
Peripheral I/O
Tri-stated
Tri-stated
Table 25. I/OPin Status During Reset and Standby Mode
相關PDF資料 |
PDF描述 |
|---|---|
| ZPSD502B1 | Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入) |
| ZPSD502B1V | Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入) |
| ZPSD512B1 | Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入) |
| ZPSD512B1V | Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入) |
| ZPSD513B1 | Field Programmable Microcontroller Peripherals(可編程邏輯，零功耗，16K位SRAM,40個可編程I/O,通用PLD有61個輸入) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZPSD413A2-12J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| ZPSD413A2-12JI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| ZPSD413A2-12LI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| ZPSD413A2-12U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| ZPSD413A2-12UI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
發布緊急采購，3分鐘左右您將得到回復。