- 您現在的位置：買賣IC網 > PDF目錄11766 > XRT81L27IV (Exar Corporation)IC LIU EI 7CH 3.3V 128TQFP PDF資料下載
參數資料
| 型號： | XRT81L27IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 16/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU EI 7CH 3.3V 128TQFP |
| 標準包裝： | 72 |
| 應用： | DECT |
| 接口： | 串行 |
| 電源電壓： | 3.3V |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-TQFP（14x20） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
á
XRT81L27
SEVEN CHANNEL E1 LINE INTERFACE UNIT WITH CLOCK RECOVERY
REV. 1.1.0
21
2.3.1
Timing Control Block
The Timing Control block contains several sub-
blocks. These functions are used to control the timing
on the input data stream such that the output meets
all system timing specifications.
2.3.2
The Transmit Clock Duty Cycle Adjust Cir-
cuit
The on-chip Pulse-Shaping circuitry in the Transmit
Section of the XRT81L27 has the responsibility for
generating pulses of the shape and width to comply
with the applicable pulse template requirement. The
widths of these output pulses are defined by the width
of the half-period pulses in the TCLK signal.
Allowing the widths of the pulses in the TCLK clock
signal to vary significantly could jeopardize the chip’s
ability to generate Transmit Output pulses of the ap-
propriate width, thereby failing the applicable Pulse
Template Requirement Specification. The chips ability
to generate compliant pulses could depend upon the
duty cycle of the clock signal applied to the TCLK in-
put pin.
In order to combat this phenomenon, the Transmit
Clock Duty Cycle Adjust circuit was designed into the
XRT81L27. The Transmit Clock Duty Cycle Adjust
Circuitry is a PLL that was designed to accept clock
pulses via the TCLK input pin at duty cycles ranging
from 30% to 70% and to regenerate these signals
with a 50% duty cycle.
The XRT81L27 Transmit Clock Duty Cycle Adjust cir-
cuit alleviates the need to supply a signal with a 50%
duty cycle to the TCLK input pin.
2.3.3
Transmit All Ones
In some conditions the system will control the chip
such that it will transmit “all ones” data onto the line. It
is possible that a valid TClk is not available and so the
MClk signal will be used to provide the timing. It
should be noted that the Local feedback will NOT in-
clude the “all ones” bit stream so this data is diverted
before going into the pulse shaper circuit.
2.4
THE PULSE SHAPING CIRCUIT
The purpose of the "Transmit Pulse Shaping" Circuit
is to generate Transmit Output pulses that comply
with the ITU-T G.703 Pulse Template Requirements
for E1 applications, even with TClk duty cycle be-
tween 30 and 70%.
As a consequence, each channel (within the
XRT81L27) will take each mark which is provided to it
via the Transmit Input Interface block, and will gener-
ate a pulse that complies with the pulse template,
presented in Figure 11, (when measured on the sec-
ondary-side of the Transmit Output Transformer).
相關PDF資料 |
PDF描述 |
|---|---|
| MS27473T20A35S | CONN PLUG 79POS STRAIGHT W/SCKT |
| 413990-2 | CONN JACK SMB VERTICAL NICKEL |
| 5226978-1 | CONN JACK BNC RT/ANG 50 OHM TIN |
| D38999/24FB99SN | CONN RCPT 7POS JAM NUT W/SCKT |
| 1-5225398-5 | CONN JACK BNC RD316DB DUAL CRIMP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT81L27IV-F | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XR-T8205CP | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telephone Ringer |
| XR-T8205P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telephone Ringer |
| XRT82D20 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT |
| XRT82D20_06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL E1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。