- 您現在的位置：買賣IC網 > PDF目錄372950 > XRT73LC00IV (EXAR CORP) E3/DS3/STS-1 LINE INTERFACE UNIT PDF資料下載
參數資料
| 型號： | XRT73LC00IV |
| 廠商： | EXAR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP44 |
| 封裝： | 10 X 10 MM, 1.40 MM HEIGHT, TQFP-44 |
| 文件頁數： | 32/53頁 |
| 文件大?。?/td> | 604K |
| 代理商： | XRT73LC00IV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
XRT73L00
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.2.0
á
29
As the line signal is transmitted from a given transmit-
ting terminal, the pulse shapes at that location are ba-
sically square. These pulses consist of a combina-
tion of “Low” and “High” frequency Fourier compo-
nents. As this line signal travels from the transmitting
terminal via the coaxial cable to the receiving termi-
nal, it is subjected to frequency-dependent loss. The
higher-frequency components of the signal is subject-
ed to a greater amount of attenuation than the lower-
frequency components. If this line signal travels over
reasonably long cable lengths (e.g., greater than 450
feet), then the shape of the pulses which were origi-
nally square is distorted and inter-symbol interference
increases.
The purpose of the Receive Equalizer is to equalize
the distortion of the incoming signal due to cable loss.
The Receive Equalizer accomplishes this by subject-
ing the received line signal to frequency-dependent
amplification which attempts to counter the frequency
dependent loss that the line signal has experienced
and to restore the shape of the line signal so that the
transmitted data and clock can be recovered reliably.
3.2.1
izer
This data sheet presents guidelines for setting the
Receive Equalizer, for the following conditions.
1.
If the overall cable length from the local Receiving
Terminal to the remote Transmitting Terminal is
NOT known.
2.
If the overall cable length from the local Receiving
Terminal to the remote Transmitting Terminal is
known.
3.2.1.1
If the Overall Cable Length is NOT
Known
Guidelines for Setting the Receive Equal-
This section presents recommendations on what
state to set the Receive Equalizer when the overall
cable-length from the local Receiving Terminal to the
remote Transmitting Terminal is NOT known. For
DS3, STS-1 and E3 applications, enable the Receive
Equalizer by setting either the REQDIS input pin “l(fā)ow”
or the REQDIS bit-field to “0”. The remainder of this
section provides an explanation why we recommend
enabling the Receive Equalizer for these applications.
3.2.1.1.1
The Use of the Receive Equalizer in a
Typical DS3 or STS-1 Application
Most System Manufacturers of equipment supporting
DS3 and STS-1 lines interface their equipment to ei-
ther a DSX-3 or STSX-1 Cross-Connect. While in-
stalling their equipment the Transmit Line Build-Out
circuit is set to the proper setting that makes the
transmit output pulse compliant with the Isolated
DSX-3 or STSX-1 Pulse Template requirements. For
the XRT73L00 this is achieved by setting the TXLEV
input pin or bit-field to the appropriate level.
When the System Manufacturer is interfacing the Re-
ceive Section of the XRT73L00 to the Cross-Connect,
they should keep aware of the following facts:
1.
All DS3 or STS-1 line signals that are present at
either the DSX-3 or the STSX-1 Cross-Connect
are required to meet the Isolated Pulse Template
Requirements per Bellcore GR-499-CORE for
DS3 applications or Bellcore GR-253-CORE for
STS-1 applications.
2.
Bellcore documents state that the amplitude of
these pulses at the DSX-3 or STSX-1 can range
in amplitude from 360mVpk to 850mVpk.
3.
Bellcore documents stipulate that the Receiving
Terminal must be able to receive this pulse-tem-
plate compliant line signal over a cable length of
0 to 450 feet from the DSX-3 or the STSX-1
Cross Connect.
These facts are reflected in Figure 18.
相關PDF資料 |
PDF描述 |
|---|---|
| XRT73L00 | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00A | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AIV | E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT75L03DIV | Telecomm/Datacomm |
| XRT75L00 | E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT73LC03A | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC03A_08 | 制造商:EXAR 制造商全稱:EXAR 功能描述:3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73LC03AES | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT73LC03AIV | 功能描述:外圍驅動器與原件 - PCI RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT73LC03AIVF | 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Serial 120-Pin LQFP |
發布緊急采購，3分鐘左右您將得到回復。