- 您現在的位置：買賣IC網 > PDF目錄10783 > XRT7300IV-F (Exar Corporation)IC LIU E3/DS3/STS-1 SGL 44TQFP PDF資料下載
參數資料
| 型號： | XRT7300IV-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 21/55頁 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 44TQFP |
| 標準包裝： | 160 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LQFP |
| 供應商設備封裝： | 44-TQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1635 XRT7300IV-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XRT7300
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.1.2
24
If the Transmit Line Build-Out circuit is disabled, then
the XRT7300 outputs partially-shaped pulses onto
the line via the TTIP and TRING output pins.
Disable the Transmit Line Build-Out circuit in the
XRT7300 by doing the following:
If the XRT7300 is operating in the Hardware Mode,
set the TXLEV input pin (pin 1) to “High”
If the XRT7300 is operating in the HOST Mode, set
the TXLEV bit-field to “1” as illustrated below.
2.4.3
Design Guideline for Setting the Transmit
Line Build-Out Circuit
The setting ofTXLEV input pin or bit-field should be
based upon the overall cable length between the
Transmitting Terminal and the Digital Cross Connect
system (where the pulse template measurements are
made).
If the cable length between the Transmitting Terminal
and the DSX-3 or STSX-1 is less than 225 feet, it is
advisable to enable the Transmit Line Build-Out cir-
cuit by setting the TXLEV input pin or bit-field to "0".
NOTE: In this case the XRT7300 outputs shaped (e.g., not
square-wave) pulses onto the line via the TTIP and TRING
output pins. The shape of this output pulse is such that it
complies with the pulse template requirements even when
subjected to cable loss ranging from 0 to 225 feet.
If the cable length between the Transmitting
Terminal and the DSX-3 or STSX-1 is greater than
225 feet, it is advisable to disable the Transmit Line
Build-Out circuit by setting the TXLEV input pin or bit-
field to "1".
NOTE: In this case the XRT7300 outputs partially-shaped
pulses onto the line via the TTIP and TRING output pins.
The cable loss that these pulses experience over long
cable lengths (e.g., greater than 225 feet) causes these
pulses to be properly shaped and comply with the appropri-
ate pulse template requirement.
2.4.4
The Transmit Line Build-Out Circuit and
E3 Applications
The ITU-T G.703 Pulse Template Requirements for
E3 states that the E3 transmit output pulse should be
measured at the Secondary Side of the Transmit Out-
put Transformer for Pulse Template compliance. In
other words, there is no Digital Cross Connect Sys-
tem pulse template requirement for E3 and the Trans-
mit Line Build-Out circuit in the XRT7300 is disabled
whenever it is operating in the E3 Mode.
2.5
INTERFACING THE TRANSMIT SECTION OF THE
XRT7300 TO THE LINE
The E3, DS3 and SONET STS-1 specification docu-
ments all state that line signals transmitted over coax-
ial cable are to be terminated with 75 Ohms. There-
fore, interface the Transmit Section of the XRT7300,
as illustrated in Figure 15 which shows two 36 Ohm
resistors in series with the primary side of the trans-
former. These two 36Ohm resistors closely match
the 75Ohm load termination resistor thereby minimiz-
ing Transmit Return Loss.
COMMAND REGISTER CR1 (ADDRESS = 0X01)
D4
D3
D2
D1
D0
TXOFF
TAOS
TXCLKINV
TXLEV
TXBIN
0
X
1
FIGURE 15. RECOMMENDED SCHEMATIC FOR INTERFACING THE TRANSMIT SECTION OF THE XRT7300 TO THE LINE
R1
36.0
R2
36.0
TTIP
TRING
1:1
BNC
T1
相關PDF資料 |
PDF描述 |
|---|---|
| VI-JTZ-MW-S | CONVERTER MOD DC/DC 2V 40W |
| VI-BNW-MX-F2 | CONVERTER MOD DC/DC 5.5V 75W |
| LTC2619IGN#TRPBF | IC DAC 14BIT R-R QUAD 16SSOP |
| SP510EM-L | IC TXRX MULTIPROTOCOL HS 100LQFP |
| AD5334BRUZ-REEL | IC DAC 8BIT QUAD VOUT 24TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT7300IVTR | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT7300IVTR-F | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT7302IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM Transceiver |
| XRT73L00 | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00A | 制造商:EXAR 制造商全稱:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
發布緊急采購，3分鐘左右您將得到回復。