- 您現在的位置：買賣IC網 > PDF目錄11830 > XR17D152IM-F (Exar Corporation)IC UART PCI BUS DUAL 100TQFP PDF資料下載
參數資料
| 型號： | XR17D152IM-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 39/68頁 |
| 文件大小： | 0K |
| 描述： | IC UART PCI BUS DUAL 100TQFP |
| 標準包裝： | 90 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-TQFP |
| 供應商設備封裝： | 100-TQFP（14x14） |
| 包裝： | 托盤 |
| 其它名稱： | XR17D152IM-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
XR17D152
á
UNIVERSAL (3.3V AND 5V) PCI BUS DUAL UART
REV. 1.2.0
44
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. This bit indicates that the transmitter is ready to
accept a new character for transmission. In addition, this bit causes the UART to issue an interrupt to the host
when the THR interrupt enable is set. The THR bit is set to a logic 1 when the last data byte is transferred from
the transmit holding register to the transmit shift register. The bit is reset to logic 0 concurrently with the data
loading to the transmit holding register by the host. In the FIFO mode this bit is set when the transmit FIFO is
empty; it is cleared when at least 1 byte is written to the transmit FIFO.
LSR[6]: Transmit Shift Register Empty Flag
This bit is the Transmit Shift Register Empty indicator. This bit is set to a logic 1 whenever the transmitter goes
idle. It is set to logic 0 whenever either the THR or TSR contains a data character. In the FIFO mode this bit is
set to one whenever the transmit FIFO and transmit shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there is no more error(s) in the FIFO.
5.8.10
Modem Status Register (MSR) - Read-Only
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits are
set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general purpose
inputs/outputs when they are not used with modem signals.
MSR[0]: Delta CTS# Input Flag
Logic 0 = No change on CTS# input (default).
Logic 1 = The CTS# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3.
MSR[1]: Delta DSR# Input Flag
Logic 0 = No change on DSR# input (default).
Logic 1 = The DSR# input has changed state since the last time it was monitored. A modem status interrupt
will be generated if MSR interrupt is enabled (IER bit-3).
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a logic 0 to a logic 1, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit-3).
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit-3).
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS (EFR bit-7) and RTS/CTS flow control select (MCR bit-2). Auto CTS flow control allows starting and
stopping of local data transmissions based on the modem CTS# signal. A logic 1 on the CTS# pin will stop
UART transmitter as soon as the current character has finished transmission, and a logic 0 will resume data
transmission. If automatic hardware flow control is not used, MSR bit-4 bit is the compliment of the CTS# input.
However in the loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may
be used as a general purpose input when the modem interface is not used.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B73-IX-F3 | CONVERTER MOD DC/DC 24V 75W |
| VE-B73-IX-F1 | CONVERTER MOD DC/DC 24V 75W |
| XR17C152CM-F | IC UART PCI BUS DUAL 100TQFP |
| VE-B73-IW-F4 | CONVERTER MOD DC/DC 24V 100W |
| XR16L784CVTR-F | IC UART FIFO 64B QUAD 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17D154 | 制造商:EXAR 制造商全稱:EXAR 功能描述:UNIVERSAL (3.3V AND 5V) PCI BUS QUAD UART |
| XR17D154CV | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D154CV-0A-EVB | 功能描述:界面開發工具 Supports D154 144 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17D154CV-F | 功能描述:UART 接口集成電路 3.3V-5V 64B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17D154CVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 64Byte FIFO 3.3V/5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D154CVTR-F |
發布緊急采購，3分鐘左右您將得到回復。