- 您現在的位置：買賣IC網 > PDF目錄1975 > XR16V598IQ100-F (Exar Corporation)IC UART FIFO 16B OCTAL 100QFP PDF資料下載
參數資料
| 型號： | XR16V598IQ100-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 39/58頁 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 16B OCTAL 100QFP |
| 標準包裝： | 66 |
| 特點： | * |
| 通道數： | 8 |
| FIFO's： | 16 字節 |
| 規程： | RS485 |
| 電源電壓： | 2.25 V ~ 3.6 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-QFP（14x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
XR16V598
44
2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO
REV. 1.0.3
4.13
Enhanced Feature Register (EFR) - Read/Write
Enhanced features are enabled or disabled using this register. Bits 3:0 provide single or dual consecutive
character software flow control selection (see Table 17). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS or DSR Flow Control.
Logic 0 = Automatic CTS/DSR flow control is disabled (default).
Logic 1 = Enable Automatic CTS/DSR flow control. Transmission stops when CTS/DSR# pin de-asserts
(HIGH). Transmission resumes when CTS/DSR# pin is asserted (LOW). The selection for CTS# or DSR# is
through MCR bit-2.
EFR[6]: Auto RTS or DTR Flow Control Enable
RTS#/DTR# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS/
DTR is selected, an interrupt will be generated when the receive FIFO is filled to the programmed trigger level
and RTS/DTR# will de-assert (HIGH) at the next upper trigger. RTS/DTR# will re-assert (LOW) when FIFO
data falls below the next lower trigger. The RTS# or DTR# output must be asserted (LOW) before the auto
RTS/DTR can take effect. The selection for RTS# or DTR# is through MCR bit-2. RTS/DTR# pin will function
as a general purpose output when hardware flow control is disabled.
Logic 0 = Automatic RTS/DTR flow control is disabled (default).
Logic 1 = Enable Automatic RTS/DTR flow control.
EFR[5]: Special Character Detect Enable
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the received data will be transferred to FIFO and ISR bit-4 will be set
to indicate detection of the special character. Bit-0 corresponds with the LSB bit for the receive character. If
flow control is set for comparing Xon1, Xoff1 (EFR [1:0]=10) then flow control and special character work
normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]=01) then flow control works
normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character
interrupt.
EFR[4]: Enhanced Function Bits Enable
Enhanced function control bit. This bit enables the enhanced functions in IER bits 7:5, ISR bits 5:4, FCR bits
5:4, MCR bits 7:5, 3:2 and MSR 7:2 bits to be modified. After modifying any enhanced bits, EFR bit-4 can be
set to a logic 0 to latch the new values. This feature prevents legacy software from altering or overwriting the
enhanced functions once set. Normally, it is recommended to leave it enabled, logic 1.
Logic 0 = modification disable/latch enhanced features. IER bits 7:5, ISR bits 5:4, FCR bits 5:4, MCR bits 7:5,
3:2 and MSR 7:2 bits are saved to retain the user settings. After a reset, all these bits are set to a logic 0 to
be compatible with ST16C550 mode (default).
Logic 1 = Enables the enhanced functions. When this bit is set to a logic 1 all enhanced features are
enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16V654DIV-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V698IQ100-F | IC UART FIFO 32B OCTAL 100QFP |
| XR16V794IV-F | IC UART FIFO 64B QUAD 64LQFP |
| XR16V798IQ-F | IC UART FIFO 64B OCTAL 100QFP |
| XR17C152IM-F | IC UART PCI BUS DUAL 100TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V654 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654_0709 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654D | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V QUAD UART WITH 64-BYTE FIFO |
| XR16V654DIV | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| XR16V654DIV-0A-EB | 功能描述:UART 接口集成電路 Supports V654 64 ld LQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。