參數資料
型號： XR16M680IM48-F
廠商： Exar Corporation
文件頁數： 37/57頁
文件大?。?/td> 0K
描述： IC UART FIFO 32B 48TQFP
標準包裝： 250
特點： *
通道數： 1，UART
FIFO's： 32 字節
規程： RS232，RS422，RS485
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-TQFP
供應商設備封裝： 48-TQFP（7x7）
包裝： 托盤
XR16M680
42
1.62V TO 3.63V HIGH PERFORMANCE UART WITH 32-BYTE FIFO
REV. 1.0.0
EFR[5]: Special Character Detect Enable
Logic 0 = Special Character Detect Disabled (default).
Logic 1 = Special Character Detect Enabled. The UART compares each incoming receive character with
data in Xoff-2 register. If a match exists, the receive data will be transferred to FIFO and ISR bit-4 will be set
to indicate detection of the special character. Bit-0 corresponds with the LSB bit of the receive character. If
flow control is set for comparing Xon1, Xoff1 (EFR [1:0]= ‘10’) then flow control and special character work
normally. However, if flow control is set for comparing Xon2, Xoff2 (EFR[1:0]= ‘01’) then flow control works
normally, but Xoff2 will not go to the FIFO, and will generate an Xoff interrupt and a special character
interrupt, if enabled via IER bit-5.
EFR[6]: Auto RTS Flow Control Enable
RTS# output may be used for hardware flow control by setting EFR bit-6 to logic 1. When Auto RTS is
selected, an interrupt will be generated when the receive FIFO is filled to the selected trigger level and RTS de-
asserts HIGH at the next upper trigger level/hysteresis level. RTS# will return LOW when FIFO data falls below
the next lower trigger level/hysteresis level. The RTS# output must be asserted (LOW) before the auto RTS
can take effect. RTS# pin will function as a general purpose output when hardware flow control is disabled.
Logic 0 = Automatic RTS flow control is disabled (default).
Logic 1 = Enable Automatic RTS flow control.
EFR[7]: Auto CTS Flow Control Enable
Automatic CTS Flow Control.
Logic 0 = Automatic CTS flow control is disabled (default).
Logic 1 = Enable Automatic CTS flow control. Data transmission stops when CTS# input de-asserts to logic
1. Data transmission resumes when CTS# returns to a logic 0.
4.17
Software Flow Control Registers (XOFF1, XOFF2, XON1, XON2) - Read/Write
These registers are used as the programmable software flow control characters xoff1, xoff2, xon1, and xon2.
For more details, see Table 5. The xoff2 is also used as auto address detect register when the auto 9-bit mode
相關PDF資料
PDF描述
XR16M681IL32-F IC UART FIFO 64B 32QFN
XR16M698IQ100-F IC UART FIFO 32B OCTAL 100QFP
XR16M770IL32-F IC UART FIFO 64B 32QFN
XR16M780IM48-F IC UART FIFO 64B 48TQFP
XR16M781IL32-F IC UART FIFO 64B 32QFN
相關代理商/技術參數
參數描述
XR16M681 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 32-BYTE FIFO AND VLIO INTERFACE
XR16M681IB25 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 32-BYTE FIFO AND VLIO INTERFACE
XR16M681IB25-0C-EB 功能描述:界面開發工具 Eval Board for XR16M681IB25 Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M681IB25-F 功能描述:UART 接口集成電路 1.62-3.63V; 32-Byte FIFO & VLIO; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M681IL24 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V UART WITH 32-BYTE FIFO AND VLIO INTERFACE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*