參數資料
型號: XR16L2551IL-F
廠商: Exar Corporation
文件頁數: 27/49頁
文件大?。?/td> 0K
描述: IC UART FIFO 16B DUAL 32QFN
標準包裝: 490
特點: *
通道數: 2,DUART
FIFO's: 16 字節
規程: RS232,RS485
電源電壓: 2.25 V ~ 5.5 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-QFN 裸露焊盤(5x5)
包裝: 托盤
其它名稱: 1016-1450
XR16L2551IL-F-ND
XR16L2551
33
REV. 1.1.3
LOW VOLTAGE DUART WITH POWERSAVE
4.13
Device Revision Register (DREV) - Read Only
This register contains the device revision information. For example, 0x01 means revision A. Prior to reading
this register, DLL and DLM should be set to 0x00.
4.14
Enhanced Feature Register (EFR)
Enhanced features are enabled or disabled using this register. Bit 0-3 provide single or dual consecutive
character software flow control selection (see Table 13). When the Xon1 and Xon2 and Xoff1 and Xoff2 modes
are selected, the double 8-bit words are concatenated into two sequential characters. Caution: note that
whenever changing the TX or RX flow control bits, always reset all bits back to logic 0 (disable) before
programming a new setting.
EFR[3:0]: Software Flow Control Select
Single character and dual sequential characters software flow control is supported. Combinations of software
flow control can be selected by programming these bits.
EFR[4]: Enhanced Function Bits Enable
Enhanced function control bit. This bit enables IER bits 4-7, ISR bits 4-5, and MCR bits 5-7 to be modified.
After modifying any enhanced bits, EFR bit-4 can be set to a logic 0 to latch the new values. This feature
prevents legacy software from altering or overwriting the enhanced functions once set. Normally, it is
recommended to leave it enabled, logic 1.
Logic 0 = modification disable/latch enhanced features. IER bits 4-7, ISR bits 4-5, and MCR bits 5-7 are
saved to retain the user settings. After a reset, the IER bits 4-7, ISR bits 4-5, and MCR bits 5-7are set to a
logic 0 to be compatible with ST16C550 mode (default).
Logic 1 = Enables the above-mentioned register bits to be modified by the user.
TABLE 13: SOFTWARE FLOW CONTROL FUNCTIONS
EFR BIT-3
CONT-3
EFR BIT-2
CONT-2
EFR BIT-1
CONT-1
EFR BIT-0
CONT-0
TRANSMIT AND RECEIVE SOFTWARE FLOW CONTROL
0
No TX and RX flow control (default and reset)
0
X
No transmit flow control
1
0
X
Transmit Xon1, Xoff1
0
1
X
Transmit Xon2, Xoff2
1
X
Transmit Xon1 and Xon2, Xoff1 and Xoff2
X
0
No receive flow control
X
1
0
Receiver compares Xon1, Xoff1
X
0
1
Receiver compares Xon2, Xoff2
1
0
1
Transmit Xon1, Xoff1
Receiver compares Xon1 or Xon2, Xoff1 or Xoff2
0
1
Transmit Xon2, Xoff2
Receiver compares Xon1 or Xon2, Xoff1 or Xoff2
1
Transmit Xon1 and Xon2, Xoff1 and Xoff2,
Receiver compares Xon1 and Xon2, Xoff1 and Xoff2
0
1
No transmit flow control,
Receiver compares Xon1 and Xon2, Xoff1 and Xoff2
相關PDF資料
PDF描述
XR68C192CV-F IC UART FIFI DUAL 44LQFP
ST16C2550IQ48-F IC DUART FIFO 16B 48TQFP
XR16C850CM-F IC UART FIFO 128B 48TQFP
XR16L2750IM-F IC UART FIFO 64B DUAL 48TQFP
ST16C2550CQ48-F IC DUART FIFO 16B 48TQFP
相關代理商/技術參數
參數描述
XR16L2551ILTR-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551IM 制造商:EXAR 制造商全稱:EXAR 功能描述:LOW VOLTAGE DUART WITH POWERSAVE
XR16L2551IM-0A-EB 功能描述:UART 接口集成電路 Supports L2551 48 ld TQFP, ISA Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551IM-0B-EB 功能描述:UART 接口集成電路 Supports L2551 48 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16L2551IM-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel