參數資料
型號： XR16C864IQTR-F
廠商： Exar Corporation
文件頁數： 14/51頁
文件大?。?/td> 0K
描述： IC UART FIFO 128B QUAD 100QFP
標準包裝： 500
特點： *
通道數： 4，QUART
FIFO's： 128 字節
規程： RS232，RS485
電源電壓： 2.97 V ~ 5.5 V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 100-BQFP
供應商設備封裝： 100-QFP（14x20）
包裝： 帶卷 (TR)
XR16C864
21
REV. 2.2.0
2.97V TO 5.5V QUAD UART WITH 128-BYTE FIFO
2.21
Sleep Mode with Auto Wake-Up
The 864 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the 864 to enter sleep mode:
s
no interrupts pending for all four channels of the 864 (ISR bit-0 = 1)
s
sleep mode of all four channels are enabled (IER bit-4 = 1)
s
modem inputs are not toggling (MSR bits 0-3 = 0)
s
RX input pins are idling at a logic 1
The 864 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no
clock output as an indication that the device has entered the sleep mode.
The 864 resumes normal operation by any of the following:
s
a receive data start bit transition (logic 1 to 0)
s
a data byte is loaded to the transmitter, THR or FIFO
s
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the 864 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the 864 is awakened by the modem inputs, a read
to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while an
interrupt is pending in any channel. The 864 will stay in the sleep mode of operation until it is disabled by
setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, CSC#, CSD# and modem input lines remain
steady when the 864 is in sleep mode, the maximum current will be in the microamp range as specified in the
DC Electrical Characteristics on page 42. If the input lines are floating or are toggling while the 864 is in sleep
mode, the current can be up to 100 times more. If any of those signals are toggling or floating, then an external
buffer would be required to keep the address, data and control lines steady to achieve the low current.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX input is idling at logic 1 or “marking” condition
during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or another
type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the system design
engineer can use a 47k ohm pull-up resistor on the RX A-D inputs.
相關PDF資料
PDF描述
XR16C864CQTR-F IC UART FIFO 128B QUAD 100QFP
XR16C854DCV-F IC UART FIFO 128B QUAD 64LQFP
XR16C854IQTR-F IC UART FIFO 128B QUAD 100QFP
ATUC64D3-A2UR IC MCU 32BIT 64KB FLASH 64TQFP
ST16C654CQ100-F IC UART FIFO 64B QUAD 100QFP
相關代理商/技術參數
參數描述
XR16C872 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16C872CQ 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16C872IQ 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 1284 PARALLEL PORT AND PLUG-AND-PLAY CONTROLLER
XR16L2450 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
XR16L2450_05 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 5.5V DUART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*