參數資料
型號: XPC8260ZUIHBC
廠商: Freescale Semiconductor
文件頁數: 3/41頁
文件大小: 0K
描述: IC MPU POWERQUICC II 480-TBGA
標準包裝: 21
系列: MPC82xx
處理器類型: 32-位 MPC82xx PowerQUICC II
速度: 200MHz
電壓: 2.5V
安裝類型: 表面貼裝
封裝/外殼: 480-LBGA
供應商設備封裝: 408-TBGA(37.5x37.5)
包裝: 托盤
MPC8260 PowerQUICC II Integrated Communications Processor Hardware Specifications, Rev. 2
Freescale Semiconductor
11
Electrical and Thermal Characteristics
2.3.1
Layout Practices
Each VCC pin should be provided with a low-impedance path to the board’s power supply. Each ground
pin should likewise be provided with a low-impedance path to ground. The power supply pins drive
distinct groups of logic on chip. The VCC power supply should be bypassed to ground using at least four
0.1 F by-pass capacitors located as close as possible to the four sides of the package. The capacitor leads
and associated printed circuit traces connecting to chip VCC and ground should be kept to less than half an
inch per capacitor lead. A four-layer board is recommended, employing two inner layers as V
CC and GND
planes.
All output pins on the MPC8260 have fast rise and fall times. Printed circuit (PC) trace interconnection
length should be minimized in order to minimize overdamped conditions and reflections caused by these
fast output switching times. This recommendation particularly applies to the address and data buses.
Maximum PC trace lengths of six inches are recommended. Capacitance calculations should consider all
device loads as well as parasitic capacitances due to the PC traces. Attention to proper PCB layout and
bypassing becomes especially critical in systems with higher capacitive loads because these loads create
higher transient currents in the VCC and GND circuits. Pull up all unused inputs or signals that will be
inputs during reset. Special care should be taken to minimize the noise levels on the PLL supply pins.
Table 5 provides preliminary, estimated power dissipation for various configurations. Note that suitable
thermal management is required for conditions above PD = 3W (when the ambient temperature is 70° C or
greater) to ensure the junction temperature does not exceed the maximum specified value. Also note that
the I/O power should be included when determining whether to use a heat sink.
Table 5. Estimated Power Dissipation for Various Configurations1
1 Test temperature = room temperature (25° C)
Bus
(MHz)
CPM
Multiplier
CPU
Multiplier
CPM
(MHz)
CPU
(MHz)
PINT (W)
2
2 P
INT = IDD x VDD Watts
Vddl
2.4
2.5
2.6
2.7
2.83
3 2.8 Vddl does not apply to HiP3 Rev C silicon.
33.3
4
133.3
2.04
2.14
2.26
2.38
2.50
50.0
2
3
100
150.0
2.21
2.30
2.45
2.59
2.69
66.7
2
2.5
133.3
166.7
2.47
2.62
2.74
2.88
3.02
66.7
2.5
166.7
2.57
2.69
2.83
2.98
3.12
66.7
2
3
133.3
200.0
2.81
2.95
3.12
3.29
3.43
66.7
2.5
3
166.7
200.0
2.88
3.05
3.22
3.38
3.55
50.0
3
4
150
200.0
2.83
3.00
3.14
3.31
3.48
Note:
相關PDF資料
PDF描述
IDT70P248L55BYGI IC SRAM 64KBIT 55NS 108PGA
XPC8260CZUIFBC IC MPU POWERQUICC II 480-TBGA
IDT70P247L55BYGI IC SRAM 64KBIT 55NS 100BGA
65801-135LF CLINCHER RECEPTACLE ASSY GOLD
65801-035LF CLINCHER RECEPTACLE ASS'-Y-GOLD
相關代理商/技術參數
參數描述
XPC8315E-RDB 制造商:Freescale Semiconductor 功能描述:
XPC850CVR50BU 功能描述:IC MPU POWERQUICC 50MHZ 256-PBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC8xx 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA(25x25) 包裝:托盤
XPC850CVR50BUR2 功能描述:IC MPU POWERQUICC 50MHZ 256-PBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC8xx 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA(25x25) 包裝:托盤
XPC850CVR66BU 功能描述:IC MPU POWERQUICC 66MHZ 256-PBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:MPC8xx 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA(25x25) 包裝:托盤
XPC850CZT50B 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Communications Controller Hardware Specifications