參數資料
型號： XCF08PVO48C
廠商： XILINX INC
元件分類： DRAM
英文描述： Platform Flash In-System Programmable Configuration PROMS
中文描述： 8M X 1 CONFIGURATION MEMORY, PDSO48
封裝： PLASTIC, TSOP-48
文件頁數： 32/46頁
文件大?。?/td> 525K
代理商： XCF08PVO48C
Platform Flash In-System Programmable Configuration PROMS
DS123 (v2.9) May 09, 2006
www.xilinx.com
32
R
T
HXT
EN_EXT_SEL hold time from CF, CE, or OE/RESET when V
CCO
= 3.3V or 2.5V
EN_EXT_SEL hold time from CF, CE, or OE/RESET when V
CCO
= 1.8V
REV_SEL setup time to CF, CE, or OE/RESET when V
CCO
= 3.3V or 2.5V
REV_SEL setup time to CF, CE, or OE/RESET when V
CCO
= 1.8V
REV_SEL hold time from CF, CE, or OE/RESET when V
CCO
= 3.3V or 2.5V
REV_SEL hold time from CF, CE, or OE/RESET when V
CCO
= 1.8V
300
–
ns
300
–
ns
T
SRV
300
–
ns
300
–
ns
T
HRV
300
–
ns
300
–
ns
Notes:
1.
2.
3.
4.
5.
6.
7.
AC test load = 50 pF for XCF01S/XCF02S/XCF04S; 30 pF for XCF08P/XCF16P/XCF32P.
Float delays are measured with 5 pF AC loads.Transition is measured at ±200 mV from steady-state active levels.
Guaranteed by design, not tested.
All AC parameters are measured with V
IL
= 0.0V and V
IH
= 3.0V.
If T
HCE
High < 2
μ
s, T
CE
= 2
μ
s.
If T
HOE
Low < 2
μ
s, T
OE
= 2
μ
s.
This is the minimum possible T
CYCO
. Actual T
CYCO
= T
CCDD
+ FPGA Data setup time.
Example:
With the XCF32P in serial mode with V
CCO
at 3.3V, if FPGA Data setup time = 15 ns, then the actual T
CYCO
= 25 ns +15 ns = 40 ns.
The delay before the enabled CLKOUT signal begins clocking data out of the device is dependent on the clocking configuration. The delay
before CLKOUT is enabled will increase if decompression is enabled.
Slower CLK frequency option may be required to meet the FPGA data sheet setup time.
10. When decompression is enabled, the CLKOUT signal becomes a controlled clock output. When decompressed data is available, CLKOUT
will toggle at the source clock frequency (either the selected internal clock frequency or the external CLK input frequency). When
decompressed data is not available, the CLKOUT pin is parked High. If CLKOUT is used, then it must be pulled High externally using a 4.7k
Ω
pull-up to V
CCO
.
11. When JTAG CONFIG command is issued, PROM will drive CF Low for at least the T
HCF
minimum.
8.
9.
Symbol
Description
XCF08P, XCF16P,
XCF32P
Units
Min
Max
相關PDF資料
PDF描述
XCF08PVOG48 Platform Flash In-System Programmable Configuration PROMS
XCF08PVOG48C Platform Flash In-System Programmable Configuration PROMS
XCF16P Platform Flash In-System Programmable Configuration PROMS
XCF16PF48 Platform Flash In-System Programmable Configuration PROMS
XCF16PFG48 Platform Flash In-System Programmable Configuration PROMS
相關代理商/技術參數
參數描述
XCF08PVO48C 制造商:Xilinx 功能描述:
XCF08PVO48C0973 制造商:Rochester Electronics LLC 功能描述: 制造商:Xilinx 功能描述:
XCF08PVO48CES 制造商:Xilinx 功能描述:
XCF08PVO48CESB 制造商:Xilinx 功能描述:
XCF08PVOG48 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*