參數資料
型號： XCF08PFS48C
廠商： XILINX INC
元件分類： DRAM
英文描述： Platform Flash In-System Programmable Configuration PROMS
中文描述： 8M X 1 CONFIGURATION MEMORY, PBGA48
封裝： PLASTIC, TFBGA-48
文件頁數： 12/46頁
文件大?。?/td> 525K
代理商： XCF08PFS48C
Platform Flash In-System Programmable Configuration PROMS
DS123 (v2.9) May 09, 2006
www.xilinx.com
12
R
internally generated CCLK signal. If BUSY is asserted
(High) by the FPGA, the configuration data must be held
until BUSY goes Low. An external data source or external
pull-down resistors must be used to enable the FPGA's
active Low Chip Select (CS or CS_B) and Write (WRITE or
RDWR_B) signals to enable the FPGA's SelectMAP
configuration process.
The Master SelectMAP configuration interface is clocked by
the FPGA’s internal oscillator. Typically, a wide range of
frequencies can be selected for the internally generated
CCLK which always starts at a slow default frequency. The
FPGA’s bitstream contains configuration bits which can
switch CCLK to a higher frequency for the remainder of the
Master SelectMAP configuration sequence. The desired
CCLK frequency is selected during bitstream generation.
After configuration, the pins of the SelectMAP port can be
used as additional user I/O. Alternatively, the port can be
retained using the persist option.
Connecting the FPGA device to the configuration PROM for
Master SelectMAP (Parallel) Configuration Mode (
Figure 9,
page 17
):
The DATA outputs of the PROM(s) drive the [D0..D7]
input of the lead FPGA device.
The Master FPGA CCLK output drives the CLK input(s)
of the PROM(s)
The CEO output of a PROM drives the CE input of the
next PROM in a daisy chain (if any).
The OE/RESET pins of all PROMs are connected to
the INIT_B pins of all FPGA devices. This connection
assures that the PROM address counter is reset before
the start of any (re)configuration.
The PROM CE input can be driven from the DONE pin.
The CE input of the first (or only) PROM can be driven
by the DONE output of all target FPGA devices,
provided that DONE is not permanently grounded. CE
can also be permanently tied Low, but this keeps the
DATA output active and causes an unnecessary I
CC
active supply current (
"DC Characteristics Over
Operating Conditions," page 26
).
For high-frequency parallel configuration, the BUSY
pins of all PROMs are connected to the FPGA's BUSY
output. This connection assures that the next data
transition for the PROM is delayed until the FPGA is
ready for the next configuration data byte.
The PROM CF pin is typically connected to the FPGA's
PROG_B (or PROGRAM) input. For the XCFxxP only,
the CF pin is a bidirectional pin. If the XCFxxP CF pin is
not connected to the FPGA's PROG_B (or PROGRAM)
input, then the pin should be tied High.
FPGA Slave SelectMAP (Parallel) Mode
(XCFxxP PROM Only)
In Slave SelectMAP mode, byte-wide data is written into the
FPGA, typically with a BUSY flag controlling the flow of data,
synchronized by an externally supplied configuration clock
(CCLK). Upon power-up or reconfiguration, the FPGA's mode
select pins are used to select the Slave SelectMAP
configuration mode. The configuration interface typically
requires a parallel data bus, a clock line, and two control lines
(INIT and DONE). In addition, the FPGA’s Chip Select, Write,
and BUSY pins must be correctly controlled to enable
SelectMAP configuration. The configuration data is read from
the PROM byte by byte on pins [D0..D7], accessed via the
PROM's internal address counter which is incremented on
every valid rising edge of CCLK. The bitstream data must be
set up at the FPGA’s [D0..D7] input pins a short time before
each rising edge of the provided CCLK. If BUSY is asserted
(High) by the FPGA, the configuration data must be held until
BUSY goes Low. An external data source or external
pull-down resistors must be used to enable the FPGA's active
Low Chip Select (CS or CS_B) and Write (WRITE or
RDWR_B) signals to enable the FPGA's SelectMAP
configuration process.
After configuration, the pins of the SelectMAP port can be
used as additional user I/O. Alternatively, the port can be
retained using the persist option.
Connecting the FPGA device to the configuration PROM for
Slave SelectMAP (Parallel) Configuration Mode (
Figure 10,
page 18
):
The DATA outputs of the PROM(s) drives the [D0..D7]
inputs of the lead FPGA device.
The PROM CLKOUT (for XCFxxP only) or an external
clock source drives the FPGA's CCLK input.
The CEO output of a PROM drives the CE input of the
next PROM in a daisy chain (if any).
The OE/RESET pins of all PROMs are connected to
the INIT_B pins of all FPGA devices. This connection
assures that the PROM address counter is reset before
the start of any (re)configuration.
The PROM CE input can be driven from the DONE pin.
The CE input of the first (or only) PROM can be driven
by the DONE output of all target FPGA devices,
provided that DONE is not permanently grounded. CE
can also be permanently tied Low, but this keeps the
DATA output active and causes an unnecessary I
CC
active supply current (
"DC Characteristics Over
Operating Conditions," page 26
).
For high-frequency parallel configuration, the BUSY
pins of all PROMs are connected to the FPGA's BUSY
output. This connection assures that the next data
transition for the PROM is delayed until the FPGA is
ready for the next configuration data byte.
相關PDF資料
PDF描述
XCF08PFSG48C Platform Flash In-System Programmable Configuration PROMS
XCF08PV Platform Flash In-System Programmable Configuration PROMS
XCF08PVG Platform Flash In-System Programmable Configuration PROMS
XCF08PVO48 Platform Flash In-System Programmable Configuration PROMS
XCF08PVO48C Platform Flash In-System Programmable Configuration PROMS
相關代理商/技術參數
參數描述
XCF08PFS48C0936 制造商:Xilinx 功能描述:MEMORY
XCF08PFS48CESB 制造商:Xilinx 功能描述:
XCF08PFSG48C 功能描述:IC PROM SRL 1.8V 8M GATE 48CSBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:- 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件
XCF08PFSG48C4039 制造商:Xilinx 功能描述:
XCF08PV 制造商:XILINX 制造商全稱:XILINX 功能描述:Platform Flash In-System Programmable Configuration PROMS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*