- 您現在的位置：買賣IC網 > PDF目錄371304 > X9530B15I-T2 Temperature Compensated Laser Diode Controller PDF資料下載
參數資料
| 型號： | X9530B15I-T2 |
| 英文描述： | Temperature Compensated Laser Diode Controller |
| 中文描述： | 溫度補償激光二極管控制器 |
| 文件頁數： | 18/30頁 |
| 文件大?。?/td> | 479K |
| 代理商： | X9530B15I-T2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
X9530
Characteristics subject to change without notice.
18 of 30
REV 3.7 8/26/04
www.xicor.com
condition. The first data byte is written to location 81h,
the second to 82h, the third to 83h, and the last one to
84h.
The four registers Control 1 through 4, have a
nonvolatile and a volatile cell for each bit. At power up,
the content of the nonvolatile cells is automatically
recalled and written to the volatile cells. The content of
the volatile cells controls the X9530’s functionality. If bit
NV1234 in the Control 0 register is set to “1”, a Write
operation to these registers writes to both the volatile
and nonvolatile cells. If bit NV1234 in the Control 0
register is set to “0”, a Write operation to these
registers only writes to the volatile cells. In both cases
the newly written values effectively control the X9530,
but in the second case, those values are lost when the
part is powered down.
If bit NV1234 is set to “0”, a Byte Write operation to
Control registers 0 or 5 causes the value in the
nonvolatile cells of Control registers 1 through 4 to be
recalled into their corresponding volatile cells, as
during power up. This doesn’t happen when the WP
pin is LOW, because Write Protection is enabled. It is
generally recommended to configure Control registers
0 and 5 before writing to Control registers 1 through 4.
When reading any of the control registers 1, 2, 3, or 4,
the Data Bytes are always the content of the
corresponding nonvolatile cells, even if bit NV1234 is
"0" (See “Control and Status Register Format”).
Read Operation
A Read operation consist of a three byte instruction
followed by one or more Data Bytes (See Figure 19).
The master initiates the operation issuing the following
sequence: a START, the Slave Address byte with the
R/W bit set to “0”, an Address Byte, a second START,
and a second Slave Address byte with the R/W bit set
to “1”. After each of the three bytes, the X9530
responds with an ACK. Then the X9530 transmits Data
Bytes as long as the master responds with an ACK
during the SCL cycle following the eigth bit of each
byte. The master terminates the read operation
(issuing a STOP condition) following the last bit of the
last Data Byte (See Figure 19).
The Data Bytes are from the memory location indicated
by an internal pointer. This pointer initial value is
determined by the Address Byte in the Read operation
instruction, and increments by one during transmission of
5 bytes
7 bytes
Address=6
Address Pointer
Ends Up Here
Address=15
Address=11
Address=7
Address=0
Figure 17. Example: Writing 12 bytes to a 16-byte page starting at location 11.
Signals from
the Master
Signals from
the Slave
Signal at SDA
S
t
a
r
t
Slave
Address
Address
Byte = 81h
A
C
K
A
C
K
1
0
1
0
0
Data Byte for
Control 1
S
t
o
p
A
C
K
A
C
K
Data Byte for
Control 4
Write
1
1
0
0
0
0
0 0
Four Data Bytes
Figure 18. Writing to Control Registers 1, 2, 3, and 4
相關PDF資料 |
PDF描述 |
|---|---|
| X9530B15I-T1 | SINGLEMODE FIBER PATCH CABLE, PLENUM SC-LC 5M |
| X9530V14I | Temperature Compensated Laser Diode Controller |
| X9530-B15I | Temperature Compensated Laser Diode Controller |
| X9530B15I | Temperature Compensated Laser Diode Controller |
| X9530-V14I | ; Sensor Input Type:Fiber-Optic; Sensing Range Max:3m; Sensor Output:PNP; Leaded Process Compatible:No; Mounting Type:DIN Rail; Peak Reflow Compatible (260 C):No; Sensor Housing:Rectangular |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9530V14I | 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530-V14I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530V14IT1 | 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530V14IT2 | 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530V14IZ | 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
發布緊急采購，3分鐘左右您將得到回復。