- 您現在的位置：買賣IC網 > PDF目錄371304 > X9530B15I-T2 Temperature Compensated Laser Diode Controller PDF資料下載
參數資料
| 型號： | X9530B15I-T2 |
| 英文描述： | Temperature Compensated Laser Diode Controller |
| 中文描述： | 溫度補償激光二極管控制器 |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 479K |
| 代理商： | X9530B15I-T2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
X9530
Characteristics subject to change without notice.
15 of 30
REV 3.7 8/26/04
www.xicor.com
X9530 Memory Map
The X9530 contains a 2176 bit array of mixed volatile
and nonvolatile memory. This array is split up into four
distinct parts, namely: (Refer to Figure 12.)
– General Purpose Memory (GPM)
– Look-up Table 1 (LUT1)
– Look-up Table 2 (LUT2)
– Control and Status Registers
The GPM is all nonvolatile EEPROM, located at
memory addresses 00h to 7Fh.
Figure 12. X9530 Memory Map
The Control and Status registers of the X9530 are
used in the test and setup of the device in a system.
These registers are realized as a combination of both
volatile and nonvolatile memory. These registers reside
in the memory locations 80h through 8Fh. The
reserved bits within registers 80h through 86h, must be
written as “0” if writing to them, and should be ignored
when reading. The reserved registers, from 88h
through 8Fh, must not be written, and their content
should be ignored.
Both look-up tables LUT1 and LUT2 are realized as
nonvolatile EEPROM, and extend from memory
locations 90h–CFh and D0h–10Fh respectively. These
look-up tables are dedicated to storing data solely for
the purpose of setting the outputs of Current
Generators I1 and I2 respectively.
All bits in both look-up tables are preprogrammed to “0”
at the factory.
Addressing Protocol Overview
All Serial Interface operations must begin with a
START, followed by a Slave Address Byte. The Slave
address selects the X9530, and specifies if a Read or
Write operation is to be performed.
It should be noted that the Write Enable Latch (WEL)
bit must first be set in order to perform a Write
operation to any other bit. (See “WEL: Write Enable
Latch (Volatile)” on page 7.) Also, all communication to
the X9530 over the 2-wire serial bus is conducted by
sending the MSB of each byte of data first.
Even though the 2176 bit memory consists of four
differing functions, it is physically realized as one
contiguous array, organized as 17 pages of 16 bytes
each.
The X9530 2-wire protocol provides one address byte,
therefore, only 256 bytes can be addressed directly.
The next few sections explain how to access the
different areas for reading and writing.
Figure 13.
Slave Address (SA) Format
0
7
Look-up Table 2
(LUT2)
Address
Size
64 Bytes
64 Bytes
16 Bytes
128 Bytes
10Fh
FFh
00h
7Fh
80h
8Fh
90h
CFh
D0h
Look-up Table 1
(LUT1)
Control & Status
Registers
General Purpose
Memory (GPM)
SA6
SA7
SA5
SA3
SA2
SA1
SA0
Device Type
Identifier
Read or
Write
SA4
Slave Address
Bit(s)
SA7–SA4
SA3–SA1
SA0
Description
Device Type Identifier
Device Address
Read or Write Operation Select
R/W
1
0
1
0
Address
Device
AS0
AS1
AS2
相關PDF資料 |
PDF描述 |
|---|---|
| X9530B15I-T1 | SINGLEMODE FIBER PATCH CABLE, PLENUM SC-LC 5M |
| X9530V14I | Temperature Compensated Laser Diode Controller |
| X9530-B15I | Temperature Compensated Laser Diode Controller |
| X9530B15I | Temperature Compensated Laser Diode Controller |
| X9530-V14I | ; Sensor Input Type:Fiber-Optic; Sensing Range Max:3m; Sensor Output:PNP; Leaded Process Compatible:No; Mounting Type:DIN Rail; Peak Reflow Compatible (260 C):No; Sensor Housing:Rectangular |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9530V14I | 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530-V14I | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Temperature Compensated Laser Diode Controller |
| X9530V14IT1 | 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530V14IT2 | 功能描述:IC LASER DIODE CTRLR 14-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9530V14IZ | 功能描述:IC LASR CTRLR 1CHAN 5.5V 14TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
發布緊急采購，3分鐘左右您將得到回復。