- 您現在的位置：買賣IC網 > PDF目錄371276 > X88C75P Port Expander and E2 Memory PDF資料下載
參數資料
| 型號： | X88C75P |
| 英文描述： | Port Expander and E2 Memory |
| 中文描述： | 端口擴展和E2內存 |
| 文件頁數： | 8/27頁 |
| 文件大?。?/td> | 125K |
| 代理商： | X88C75P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
X88C75 SLIC
E
2
8
Figure 8. Setting the SFR Map Register
Figure 9. Setting Program Memory Map Register
BITS 7:6
Setting these two bits to any combination other than “00”
or “11” will interfere with device proper operation.
E
2
Memory Map Register (EEM)
Default = 08
0
0
LAM
0
RST
A15
A14
A13
7
6
2887 ILL F11
5
4
3
2
1
0
A15-A13
Modifying these three bits changes the location of the
program memory within the address map.The A15-A13
correspond to the upper three address bits of the 8K-
byte page where program memory will be mapped.
RST
The RST bit controls the polarity of the RESET input pin.
“0” = RESET is Active LOW
“1” = RESET is Active HIGH
LAM
Port B can be configured as either a general purpose
I/O port (normal I/O mode), or latched address mode
(LAM). The LAM option programs port B to output the
demultiplexed low order byte of the address latched into
the X88C75 by ALE. The LAM bit selects between these
two modes.
“0” = PORT B is I/O Port
“1” = Port B outputs low address byte (A7-A0)
Setting the Mapping Registers
The mapping registers are written using a modified
version of the Software Data Protection sequence. All
timings must adhere to the normal Software Data Pro-
tection sequence.
The complemented contents of the SFR map register
and the E
2
memory map register can be read by the
microcontroller at their corresponding SFR addresses.
The physical memory location of these registers can be
derived by adding the following offset to the SFR base
address:
SFR Map Register
00H
E
2
Memory Map Register
38H
If the regions specified in the map registers overlap, only
the SFR will be accessible.
AA
b2
P 555
b1 b0
55
b2
AAA
AAA
b1 b0
A0
b2
P 555
b1 b0
AA
b2
P 555
b1 b0
D0
Delay of t
WC
Exit Routine
b2
P
2887 ILL F12.1
b1 b0
XXX
Desired
Value
b2
P
b1 b0
X = Don’t Care
B[2:0] = E2M [2:0]
P = Address bit (A12) of the
memory plane not being read.
P
AA
b2
P 555
b1 b0
55
b2
AAA
AAA
b1 b0
A0
b2
P 555
b1 b0
AA
b2
P 555
b1 b0
E0
b2
P
2887 ILL F13.1
b1 b0
XXX
Desired
Value
b2
P
b1 b0
P
Delay of t
WC
Exit Routine
X = Don’t Care
B[2:0] = E2M [2:0]
P = Address bit (A12) of the
memory plane not being read.
相關PDF資料 |
PDF描述 |
|---|---|
| X88C75PI | Port Expander and E2 Memory |
| X88C75PM | Port Expander and E2 Memory |
| X9102P | Digital Potentiometer |
| X9102PI | Digital Potentiometer |
| X9102S | Digital Potentiometer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X88C75PI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X88C75PM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X8934 | 功能描述:固態繼電器-工業安裝 0381 SLD. R RELAY RoHS:否 制造商:Crydom 控制電壓范圍:4 VDC to 32 VDC 負載電壓額定值:7 VDC to 72 VDC 負載電流額定值:160 A 觸點形式: 輸出設備:SSR 安裝風格:Panel |
| X8989-34 | 制造商:Cooper Crouse-Hinds 功能描述: 制造商:CROUSE-HINDS/COOPER 功能描述: |
| X89C205VGEAF | 制造商:USMC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。