- 您現在的位置：買賣IC網 > PDF目錄359317 > V29LC51000 (Mosel Vitelic, Corp.) 512 KILOBIT 65,536 x 8 BIT 5 VOLT CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | V29LC51000 |
| 廠商： | Mosel Vitelic, Corp. |
| 英文描述： | 512 KILOBIT 65,536 x 8 BIT 5 VOLT CMOS FLASH MEMORY |
| 中文描述： | 512千比特，65536 × 8位5伏的CMOS閃存 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 52K |
| 代理商： | V29LC51000 |
8
V29LC51000 Rev. 0.4 October 2000
MOSEL V ITELIC
V29LC51000
FUNCTIONAL DESCRIPTION
Read Cycle
A read cycle is performed by holding both CE
and OE signals LOW. Data Out becomes valid only
when these conditions are met. During a read cycle
WE must be HIGH prior to CE and OE going LOW.
WE must remain HIGH during the read operation
for the read to complete (see Table 1).
Output Disable
Returning OE or CE HIGH, whichever occurs first
will terminate the read operation and place the l/O
pins in the HIGH-Z state.
Standby
The device will enter standby mode when the CE
signal is HIGH. The l/O pins are placed in the
HIGH-Z, independent of the OE signal.
Command Sequence
The V29LC51000 does not provide the
“
reset
”
feature to return the chip to its normal state when
an incomplete command sequence or an
interruption has happened. In this case, normal
operation (Read Mode) can be restored by issuing
a
“
non-existent
”
command sequence, for example
Address: 5555H, Data FFH.
Byte Program Cycle
The V29LC51000 is programmed on a byte-by-
byte basis. The byte program operation is initiated
by using a specific four-bus-cycle sequence: two
unlock program cycles, a program setup command
and program data program cycles (see Table 2).
During the byte program cycle, addresses are
latched on the falling edge of either CE or WE,
whichever is last. Data is latched on the rising edge
of CE or WE, whichever is first. The byte program
cycle can be CE controlled or WE controlled.
Sector Erase Cycle
The V29LC51000 features a sector erase
operation which allows each sector to be erased
and reprogrammed without affecting data stored in
other sectors. Sector erase operation is initiated by
using a specific six-bus-cycle sequence: Two
unlock program cycles, a setup command, two
additional unlock program cycles, and the sector
erase command (see Table 2). A sector must be
first erased before it can be reprogrammed. While
in the internal erase mode, the device ignores any
program attempt into the device. Sector erase is
completed in 10ms max. The V29LC51000 is
shipped with pre-erased sectors (all bits = 1).
512
512
512
512
V29LC51001
00000H
L51001-13
Table 1. Operation Modes Decoding
NOTES:
1.
2.
X = Don
’
t Care, V
IH
= HIGH, V
IL
= LOW. V
H
= 12.5V Max.
PD: The data at the byte address to be programmed.
Decoding Mode
CE
OE
WE
A
0
A
1
A
9
I/O
Read
V
IL
V
IL
V
IH
A
0
A
1
A
9
READ
Byte Write
V
IL
V
IH
V
IL
A
0
A
1
A
9
PD
Standby
V
IH
X
X
X
X
X
HIGH-Z
Output Disable
V
IL
V
IH
V
IH
X
X
X
HIGH-Z
相關PDF資料 |
PDF描述 |
|---|---|
| V29LC51001 | 1 MEGABIT 131,072 x 8 BIT 5 VOLT CMOS FLASH MEMORY |
| V29LC51002 | 2 MEGABIT 262,144 x 8 BIT 5 VOLT CMOS FLASH MEMORY |
| V300A48H250B | 300Vin / 48Vout / 250Watts DC-DC Converter Module |
| V300A48T150B | 300Vin / 48Vout / 150Watts DC-DC Converter Module |
| V300B15H100B | 24Vin / 15Vout / 100Watts DC-DC Converter Module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| V29LC51001 | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:1 MEGABIT 131,072 x 8 BIT 5 VOLT CMOS FLASH MEMORY |
| V29LC51002 | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:2 MEGABIT 262,144 x 8 BIT 5 VOLT CMOS FLASH MEMORY |
| V2A-10P | 功能描述:BRIMLESS, LIGHTWEIGHT CLEAR ACET 制造商:3m 系列:* 零件狀態:在售 標準包裝:1 |
| V2AAA-B | 制造商:Rayovac 功能描述:0 |
| V2AF | 制造商:OMRON 制造商全稱:Omron Electronics LLC 功能描述:Motor Driven Hybrid Card Reader |
發布緊急采購，3分鐘左右您將得到回復。