- 您現在的位置：買賣IC網 > PDF目錄225404 > UCC2919DTR (TEXAS INSTRUMENTS INC) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 PDF資料下載
參數資料
| 型號： | UCC2919DTR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | GREEN, PLASTIC, MS-012AC, SOIC-16 |
| 文件頁數： | 3/27頁 |
| 文件大?。?/td> | 701K |
| 代理商： | UCC2919DTR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
UCC2919
UCC3919
SLUS374C JULY 1999 REVISED NOVEMBER 2005
11
www.ti.com
APPLICATION INFORMATION
estimating CT(min) when using power limiting
If power limiting is used, the calculation of CT(min) for a given COUT becomes considerably more complex,
especially with a resistive load. This is because the CT charge current becomes a function of VOUT, which is
changing with time. The amount of capacitance that can be charged (without causing a fault) when using power
limiting will be significantly reduced for the same value CT, due to the shorter tON time.
The charge current contribution from the power limiting circuit is defined as:
I
PL ^
V
IN *
V
OUT *
V
PL
R
PL
t0: Normal condition Output current is nominal, output voltage is at positive rail, VCC.
t1: Fault control reached Output current rises above the programmed fault value, CT begins to charge with 35 A + IPL.
t2: Maximum current reached Output current reaches the programmed maximum level and becomes a constant current with value IMAX.
t3: Fault occurs CT has charged to 1.5 V, fault output goes low, the FET turns off allowing no output current to flow, VOUT discharges to GND.
t4: Retry CT has discharged to 0.5 V, but fault current is still exceeded, CT begins charging again, FET is on, VOUT increases.
t3 to t5: Illustrates < 3% duty cycle depending upon RPL selected.
t6 = t4
t7: Fault released, normal condition return to normal operation of the circuit breaker
UDG97073
Figure 3.
(14)
相關PDF資料 |
PDF描述 |
|---|---|
| UCC3580N-3 | 1.2 A SWITCHING CONTROLLER, 430 kHz SWITCHING FREQ-MAX, PDIP16 |
| UCC3813PW-2 | 1 A SWITCHING CONTROLLER, 52 kHz SWITCHING FREQ-MAX, PDSO8 |
| UCC3813PW-4G4 | 1 A SWITCHING CONTROLLER, 52 kHz SWITCHING FREQ-MAX, PDSO8 |
| UCC3813D-0G4 | 1 A SWITCHING CONTROLLER, 52 kHz SWITCHING FREQ-MAX, PDSO8 |
| UCC3941-5D | SWITCHING REGULATOR, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCC2919DTRG4 | 功能描述:熱插拔功率分布 3-8V Single Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC2919PW | 功能描述:熱插拔功率分布 3-8V Single Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC2919PWG4 | 功能描述:熱插拔功率分布 3-8V Sgl Hot-Swap IC Industrial Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| UCC2920DP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| UCC2921 WAF | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。