- 您現在的位置：買賣IC網 > PDF目錄384028 > TPS730XX (Texas Instruments, Inc.) LOW-NOISE, HIGH PSRR, RF 200-mA LOW-DROPOUT LINEAR REGULATORS PDF資料下載
參數資料
| 型號： | TPS730XX |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | LOW-NOISE, HIGH PSRR, RF 200-mA LOW-DROPOUT LINEAR REGULATORS |
| 中文描述： | 低噪聲，高PSRR，射頻200毫安低壓降線性穩壓器 |
| 文件頁數： | 7/13頁 |
| 文件大?。?/td> | 323K |
| 代理商： | TPS730XX |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁
www.ti.com
APPLICATION INFORMATION
TPS730xx
GND
EN
NR
IN
OUT
V
IN
V
OUT
V
IN
V
OUT
2.2
μ
F
0.01
μ
F
(1)
0.1
μ
F
NOTE: (1) This capacitor is optional.
External Capacitor Requirements
A 0.1
μ
F or larger ceramic input bypass capacitor, connected between IN and GND and located close to the
TPS730xx, is required for stability and improves transient response, noise rejection, and ripple rejection. A
higher-value input capacitor may be necessary if large, fast-rise-time load transients are anticipated or the device
is located several inches from the power source.
Board Layout Recommendation to Improve PSRR and Noise Performance
To improve ac measurements like PSRR, output noise, and transient response, it is recommended that the board
be designed with separate ground planes for V
IN
and V
OUT
, with each ground plane connected only at the GND
pin of the device. In addition, the ground connection for the bypass capacitor should connect directly to the GND
pin of the device.
TPS730xx
SBVS054H–NOVEMBER 2004–REVISED OCTOBER 2007
The TPS730xx family of low-dropout (LDO) regulators has been optimized for use in noise-sensitive
battery-operated equipment. The device features extremely low dropout voltages, high PSRR, ultralow output
noise, low quiescent current (170
μ
A typically), and enable-input to reduce supply currents to less than 1
μ
A when
the regulator is turned off.
A typical application circuit is shown in
Figure 16
.
Figure 16. Typical Application Circuit
Like most low dropout regulators, the TPS730xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance is 2.2
μ
F. Any 2.2
μ
F or larger
ceramic capacitor is suitable, provided the capacitance does not vary significantly over temperature. If load
current is not expected to exceed 100mA, a 1.0
μ
F ceramic capacitor can be used.
The internal voltage reference is a key source of noise in an LDO regulator. The TPS730xx has an NR pin which
is connected to the voltage reference through a 250k
internal resistor. The 250k
internal resistor, in
conjunction with an external bypass capacitor connected to the NR pin, creates a low pass filter to reduce the
voltage reference noise and, therefore, the noise at the regulator output. In order for the regulator to operate
properly, the current flow out of the NR pin must be at a minimum, because any leakage current creates an IR
drop across the internal resistor thus creating an output error. Therefore, the bypass capacitor must have
minimal leakage current. The bypass capacitor should be no more than 0.1
μ
F to ensure that it is fully charged
during the quickstart time provided by the internal switch shown in the
Functional Block Diagrams
.
As an example, the TPS73018 exhibits only 33
μ
V
RMS
of output voltage noise using a 0.01
μ
F ceramic bypass
capacitor and a 2.2
μ
F ceramic output capacitor. Note that the output starts up slower as the bypass capacitance
increases due to the RC time constant at the NR pin that is created by the internal 250k
resistor and external
capacitor.
Copyright 2004–2007, Texas Instruments Incorporated
Submit Documentation Feedback
7
相關PDF資料 |
PDF描述 |
|---|---|
| TPS730XX_07 | LOW-NOISE, HIGH PSRR, RF 200-mA LOW-DROPOUT LINEAR REGULATORS |
| TPS73615DBV | Cap-Free, NMOS, 400mA Low-Dropout Regulator with Reverse Current Protection |
| TPS73612DBV | Cap-Free, NMOS, 400mA Low-Dropout Regulator with Reverse Current Protection |
| TPS73612DBVG4 | Cap-Free, NMOS, 400mA Low-Dropout Regulator with Reverse Current Protection |
| TPS73612DBVR | Cap-Free, NMOS, 400mA Low-Dropout Regulator with Reverse Current Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS73101DBVR | 功能描述:低壓差穩壓器 - LDO Cap Free NMOS 150mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS73101DBVRG4 | 功能描述:低壓差穩壓器 - LDO Cap Free NMOS 150mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS73101DBVT | 功能描述:低壓差穩壓器 - LDO Cap Free NMOS 150mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| TPS73101DBVT | 制造商:Texas Instruments 功能描述:V REG LDO 0.15A 73101 SOT-23-5 |
| TPS73101DBVTG4 | 功能描述:低壓差穩壓器 - LDO Cap Free NMOS 150mA RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。